A single-phase inductive load consists of aresistance R (in ohms) in series with an inductor L(in henry). If the voltage across the load isrms 20°,and the operating frequency is w rad/s,what will be the total complex power absorbed bythe load?12а.rmsjwl12b. jul|V rms|12С.rmsR+ jwLd.12rmsR-jwL

It is given that: resistance=RInductance=LVoltage across load=Vrms∠0°frequency=ω

A single-phase inductive load consists of a resistance R (in ohms) in series with an inductor L (in henry). If the voltage across the load is V ms Z0°,and the operating frequency is w rad/s, what will be the total complex power absorbed by the load?

A single-phase inductive load consists of a resistance R (in ohms) in series with an inductor L (in henry). If the voltage across the load is V ms Z0°,and the operating frequency is w rad/s, what will be the total complex power absorbed by the load?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Related questions

Q: Paramagnetic materials cannot be magnetized. Select one: True False

A: False

Q: 12/ Calculate the effective value of the exponential function shown below 20(1 – e-100t) v(t) 20e-50...

Q: Yo 2-to-4 4 4-to-1 Decoder So MUX Y2 1/2 So C-

A: Multiplexer: It has many input and one output terminal so this is also called many to one.

Q: A 50 V range voltmeter is connected across the terminals "A" and "B" of the circuit shown in figure ...

Q: Define rectification. List different types of rectifiers.

A: Rectification is the process by which an alternating current is converted into direct current and al...

Q: Question No. 2: Let z1 = 2 + jand z2 = -3 + j6. (a) Compute the polar form of z1 and z2. (b) Compute...

Q: b) The analogue signal is defined as: v (t )= 5sin(2x 5001) + Ssin(2x 750r) is sampled as shown in F...

Q: A step in a space vehicle checkout depends on four sensors (A,B,C,D) . Every circuit is functioning ...

A: Given that 4 variables acts as sensor variable. Now i am writing the truth table of 4 variable ,in t...

Q: Design a passive RC low pass filter (see Fig. 14.7) with a cutoff frequency of 100 Hz using a 4.7µF ...

Q: 13.) Given the star connection, convert into equivalent delta connection 1 p and solve for resistanc...

A: The solution is given below

Q: Calculate Total Resistance

A: This question belongs to circuit theory . It is based on the calculation of equivalent resistance of...

Q: kr = Eripplerms/Eave,

A: Equation of line with slope is- y=y2-y1x2-x1x+C

Q: A coil RL is connected in series with a capacitor across the 220 V, 60 hz, AC supply. If this circui...

Q: How many lines are there in an NTSC signal? a) 1024 b) 1856 c) 625 d) 525

A: The NTSC stands for National Television system Committee and the NTSC Signal is used in television s...

Q: a) Find the inverse Laplace transform for the following functions: 12 F(s) = 200 X(s) = s(s +10) g²+...

A: Solve the first question, unless the student has asked for a specific question to be solved, subject...

Q: 230V Primary, 12v Secondary T1= 250mA stepdown transformer 12 D5 230V AC IN T1 1A Bridge IC2 7812 R1...

A: Single-phase Bridge circuit: It produces the DC output and takes AC input. This is a type of rectifi...

Q: Q2) A lossless transmission line is terminated with a 1002 load. If VSWR on the line is 1.5, fined t...

A: Given data, Load impedance, ZL=100 Ω VSWR=1.5

Q: → XCF) = SCf - 2000 +56(f+200) + [6(F-300)+ S(F+30) > XE) = 2-56(F-2000) +2-5 6CF+2000) + 1-5 6(F -3...

Q: A power transformer rated 8MVA, 34.5 kV/230 V is connected delta-delta.What is the phase current of ...

A: The solution is given below

Q: 2nu(-n) 0.1nu(-n) + 0.2nu(-n) Determine if stable system or not using infinite geometric series form...

Q: Given the points T (5, 20°, 120°) to P (2, 80°, 30°): find the unit vector in spherical coordinates ...

Q: 200 t. SAS. 4.

A: The solution is given below

Q: 4. A step-down transformer is used to change 220 to 12 V. If a resistive load consuming 3mW is conne...

A: This question belongs to electrical machine . It is based on the relation between primary and second...

Q: Question # 01: Apply the knowledge gained from the ac analysis of BJT to construct the AC equivalent...

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any ...

Q: Si 1. Vp, VR and I, + E =8V 2.2KQ (a)

Q: G6 GA C(s) G3 G2 6 G1 R(s) 1 G7 G8 G9

Q: A 500 hp, 2,200V, 3-phase star connected synchronous motor has a synchronous impedance of 0.4 + j4 o...

Q: Q2. Analyze the output voltage Vo in the network efficiently for triangular input signal Vi shown in...

Q: 1. In the circuit of Fig., calculate the average power absorbed by the resistor and inductor. Find t...

Q: 2. A capactance is rated 100 kVar, 380 volts, 50 hz. What will its rating be at 60 Hz 220 V? 50Kvar ...

Q: F1Β (A' + AC) F2 = (A+ C')(B + B'C') A В F1 F2

Q: Please show the complete step by step solution thank you so much. A certain current lags the voltag...

Q: 1.Explain what will happen if two current sources of different magnitude are connected in series 2...

A: Voltage source: It is an electrical component that has a fixed value of voltage. Current source: It ...

Q: 9. A 30 ohm resistor is connected in parallel with a 0.106 H inductor. The parallel combination is t...

Q: 2) DC transistor analysis: Find the indicated DC values: Vbase, Vemitter, Vcollector, Icollector Voc...

Q: 5/ Compute the r.m.s and average values of the voltage waveform shown below v(t) 4 →t(msec) 1 -4 21

A: Calculation of r.m.s. (root mean square) and average values of the given voltage waveform : We know...

Q: 1. For the diode circuit shown in Figure C1, assume the Turn-On voltage of LED1 is 2.0V and LED2 is ...

Q: A 50 and 100 microfarad capacitors are connected in series and across 100sin(w+30) voltage. Write th...

Q: Three impedance Z1=1-j4, z2=-6. and z3 = 4 +j3 respectively are connected in series parallel. Z1 is ...

A: In this question, We need to determine the voltage across the parallel of Z2 and Z3. If Three impe...

Q: Describe in your own words with proper diagram and characteristics curve : why the application of a ...

A: MOSFET- MOSFET is electronic device which mainly used as switch and amplifier. It has four port as m...

Q: A Boolean function fk of two variables A and B is defined as follows: fk (0, 0) = fk (0, 1) = fk (1,...

A: NOR gate: This gate has 2 inputs and one output. It shows output 1 when both inputs are active low ‘...

Q: 3. A certain current lags the voltage by 36 electrical degrees. The voltage waveform is increasing p...

A: Any time domain signal can be sinusoidal, DC signal or any curve signal. Sinusoidal signals are peri...

Q: $ 2.2 Load-Line Analysis 1. (a) Using the characteristics of Fig. 2.131b, determine Ip, Vp, and Vg f...

Q: We know the Fourier coefficients a,, b, of some signal which is being transmitted. The transmitter m...

A: The fourier coefficients are affected by doubling and shifting the modified parameters are written...

Q: $ 2.4 Series Diode Configurations with DC Inputs 5. Determine the current / for each of the configur...

Q: Q3) Design a three-section binomial transformer to match a 40N load to al502 transmission line, and ...

Q: all ____ receptacle outlets used in technical applications shall be gfci protacted .

Q: Write all pertinent computations to justify your final answer. Final answers must be enclosed with a...

Q: 150kN, V1 = 3v, V2 = 6v, V3 = 9v, Rı = 500KN, R2 = 1MN, and R3 = 800kN. 4. Calculate the output volt...

Q: A2 3:2 220V 1k V2 V3 АЗ 6. What is A3 reading? 4. What is A1 reading? 5. What is A2 reading? 132mA 2...

Question

A single-phase inductive load consists of a
resistance R (in ohms) in series with an inductor L
(in henry). If the voltage across the load is
rms 20°,and the operating frequency is w rad/s,
what will be the total complex power absorbed by
the load?
12
а.
rms
jwl
12
b. jul|V rms|
12
С.
rms
R+ jwL
d.
12
rms
R-jwL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance calculation is D12=D23=D31=D. Select one: True False
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
A load is said to have a leading power factor. Is it capacitive or inductive? Is the reactive power positive or negative? Repeat for a load with lagging power factor.
1. a) Find the rms magnitude and the phase angle of ICA in the circuit shown. 2. b) What percent of the average power delivered by the three-phase source is dissipated in the three-phase load?
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.