A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45. The load is resistance with the value of 10 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (ir1, ir3, ir1, andir 3) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor

A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45. The load is resistance with the value of 10 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (ir1, ir3, ir1, andir 3) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3 phase bridge inverter is operated in 180 degree mode. If obtained rms value of fundamental component of line voltage is 225 V, then ___________________is the inverter supply DC voltage.
A three-phase to three-phase, three-pulse cycloconverter operating in circulating current-free such that the input / output frequency ratio is fi / fo = 9. What are typical frequencies of the low-order higher harmonics ?
4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage
A 3 phase bridge inverter is operated from 224 V DC supply in 120 degree mode. The obtained rms value of fundamental component of line voltage is
Define a cycloconverter and write its application areas
(hat akımı=line current, faz akımı=phase current) In the 3-phase delta loaded inverter circuit, there is an R (ohmic) load as the load. 3 IGBTs are triggered at the same time in the circuit. For the values given below, calculate the product of the phase-to-phase effective voltage (Volt) measured by the V voltmeter, and the phase current effective value (Amper) measured by the A ammeter. (result: V*A) E=350 Volt, R=14 Ohm, f=50 Hz A) 6482.5 B) 7354.8 C) 3583.1 D) 5833.3 E) 4659.2
Consider a three-phase DC/AC inverter with a DC bus voltage rate at600 V. Assume the DC bus voltage can drop during a discharge cycleto 350 V DC. Determine the AC bus voltage range and for a modulationindex of 0.9
Investigate the operation principle of 3- phase inverter for 120°-Y conduction interval (by sketching phase-to-phase and phase-to-neutral voltages and terminal currents).
To the following 3-phase inverter (in) R=5Ωvert and L=23 mHA star connected load is available. The inverter is 50 Hz and the input source voltage isSince Vdc=220 Volts.a) Effective value of line voltage VLb) Effective value of phase voltage Vpc) Effective value of VL1 Line voltage at main frequencyd) Effective value of phase voltage Vp1 at main frequencye) Find THD
4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) a) Draw the circuit b) Plot the load current, showing the load voltage and semiconductor currents. c) Load voltage is effective calculate the value d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage
A lossless single phase inverter is connected to AC bus. The real power of AC load is 20 kW and the AC generator nominal power is 12 kW. The efficiency of inverter is 95%. Calculate the required power from inverter. Compute the reactive power of the inverter. The inverter volage is 232 V and the generatorvoltage is 230 V. The decoupling reactance is 0.5 ohm.
For a three phase bridge inverter with delta connected resistive load, plot the three output voltages and output currents for the 120 degree and 180 degree conduction type