A slider (1.8 kg) moves along a smooth vertical shaft. It is released from rest against the elastic spring having a stiffness of 1750 N/m and has been compressed a Determine the acceleration and velocity of the slider when y=0.15m SMOOTH SHATT distance of 150mm. SLIDER m/s SPRING m/s² a ド*1750 ト COMPRESSED @ A DISTANTE OF 5OWmm

A slider (1.8 kg) moves along a smooth vertical shaft. It is released from rest against the elastic spring having a stiffness of 1750 N/m and has been compressed a Determine the acceleration and velocity of the slider when y=0.15m SMOOTH SHATT distance of 150mm. SLIDER m/s SPRING m/s² a ド*1750 ト COMPRESSED @ A DISTANTE OF 5OWmm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

: Block B has a mass m and is released from rest when it is on top of cart A, which has a mass of 3kg. Determine the tension in cord CD needed to hold the cart from moving while B slides down A. Neglect friction. =30o
Calculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Situation 1: A beam whose moment of inertia is 0.0036 m4 at portion CB and E = 220 GPa is subjected to a load of intensity q = 20 kN/m and L = 6 meters. 1. If support B is removed, Calculate the deflection at point B. 2. If support B is present, Calculate the value of reaction at support B. 3. Calculate the deflection at point C if support B is present.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
The belt-driven pulley and attached disk are rotating with increasing angular velocity. At a certain 2instant the speed v of the belt is 1.5 m/s, and the total acceleration of point A is 75 m/s . For this instant determine (a) the angular acceleration of the pulley and disk, (b) the total acceleration of point B, and (c) the acceleration of point C on the belt.
Determine the magnitude of the reaction at the bottom of the ladder. The top of the 15kg ladder is leaning against a very smooth vertical wall. Assume thatbthe mass center of the painter is directly above his feet and that the coefficient of friction between the horizontak ground and ladder is 0.25
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
The 100-mm-diameter pulley shown fits loosely on a 10-mm-diameter shaft for which the coefficient of static friction is Determine the minimum tension T in the belt needed to (a) raise the 100-kg block and (b) lower the block. Assume that no slipping occurs between the belt and pulley and neglect the weight of the pulley Choices: A. TMAX = 1075 N, TMIN = 906 N B. TMAX = 1075 N, TMIN = 690 N
For the built-up shape shown in the figure, determine: a. The location of the plastic neutral axis from the top edge of the flange in mm (ANS 11). b. The plastic section modulus of about the horizontal axis in x106mm3 (ANS 0.214) c. The plastic moment with bending about the vertical axis if Fy = 345 Mpa kN-m. round of to the nearesrt whole number (ANS 43).
The position of the slider P in the rotating slotted arm OA is controlled by a power screw as shown. At the instant represented, θ˙ = 5.4 rad/s and θ¨ = -35 rad/s2. Also at this same instant, r = 396 mm, r˙ = -251 mm/s, and r¨ = 0. For this instant determine the r- and θ-components of the acceleration of P.
2.50) A 12 m simply supported beam with 30 kN load @ the center, if EI = 6000kN * m ^ 2 what is the maximum deflection? A. 150 mm C. 170 mm B. 160 mm D. 180 mm 2.51) A 2 in by 4 in rectangular bar is subjected to a bending load of 10 kN·m, find moment of inertia of the bar. A. 9.67 in C. 12.33i * n ^ 4 B. 10.67 in D. 14.33i * n ^ 4 A 10 m simply supported beam with 25 KN load is 3 m from the left end, what is the maximum 2.52) slope at the left end (EI = 8000kN * m ^ 2) ^ prime C. 0.0765 rad D. 0.1823 rad