a soil sample was determined to have a water content of 8% and a degree of saturation of 42%. After adding some water, the degree of saturation was altered to 53%. take the specific gravity of the soil solids to be 2.7. assuming no change in the volume of the voids, determine the following

a soil sample was determined to have a water content of 8% and a degree of saturation of 42%. After adding some water, the degree of saturation was altered to 53%. take the specific gravity of the soil solids to be 2.7. assuming no change in the volume of the voids, determine the following

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

Q: Q2/ Answer the followings with drawing sketch: A/ briefly explain what is construction joint and…

A: Construction Joint: It is type of concrete joint that is used when a new section of concrete is…

Q: Calculate the vertical reaction at B. Let P = 10 kips and W = 4 kips/ft. Assume support at B as…

Q: Draw the shear and moment diagrams for the cantilever beam shown in figure below. 40 lb/ft 12 ft 20…

A: Given Cantilever Beam with a UDL , a point load and a concentrated moment. Required To draw the…

Q: The viscosity of a certain fluid is 2 × 10-4 poise. its viscosity in both (a) Sl and (b) BG…

A: Given : viscosity of a certain fluid = 2 × 10-4 poise. Required : viscosity in both (a) Sl and (b)…

Q: supported beam as shown, with an allowable flexural stress of 15MPa, determine the following: 1.…

Q: A sound wave is observed to travel through a liquid with a speed of 1270 m/s. The specific gravity…

Q: 15. A backfill of a retaining wall consists of y=19 kN/m³ which is 6 m high. Find the lateral earth…

A: Given data: A backfill of a retaining wall consist, Y = 19 kN/m3 Height, H = 6 m Coefficient of…

Q: y' = sec x - y tan x.

A: dydx+ytanx = sec xThe given equation is of the formdydx + Py = QI.f = e∫Pdx = e∫tan xdx =…

Q: a soil sample was determined to have a water content of 8% and a degree of saturation of 42%. After…

Q: is subjected to a tensile load of 106 N at the ends.

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A pair of overlap aerial photograph was taken with a camera from an altitude of 3000 m above datum.…

A: Given- H=300 mfocal length f=120 mdistance between principal points b=71.2 mmAircraft base=Bchimney…

Q: Could you explain the calcutions in more detail like why you used does numbers in does ways

Q: a)Determine the magnitude of the projected component of the force F = [ 60 i + 12 j - 35 k ] N along…

A: Given :

Q: Determine the work required to lift a box that weighs 100 N 1.5 m above the ground, as shown .

A: Given data: Weight of box = 100 N distance of lift = 1.5 m

Q: Assume straight line instead of parabola for stress-strain curve of concrete as follows and partial…

A: Given- RCC sectionwidth b=300 mmeffective depth d=500 mm3 bars of grade Fe415dia=16 mM20 concrete…

Q: Problem 4.39 Consider the system shown in (Figure 1). Figure 1 of 1 45° 7 ft F= 80 lb 3 ft B 1.5 ft…

Q: The unsymmetrical I-section is cover plated with a 300mm W x 6mm thkplate. Use A 992 steel. 1)…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: " Two concentric glass tubes immersed in water as shown in figure. The outer tube has diameter of (D…

A: Capillary Rise Capillary tubes are thin cylindrical tubes with extremely tiny diameters. The liquid…

Q: Q3) A leveling staff setup on point R of elevation (-8.79 m), is observed from point A ,where the…

Q: 3. Determine the length b of the triangular load and its position a on the beam such that the…

A: Reaction =012×6×b-2×a+b=03b-2a-2b=0b=2a...........1

Q: "Prob. 6.3-8. The structural steel wide-flange beam shown in Fig. P6.3-8 is a W8 x 48 section (See…

Q: Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum…

Q: A circular channel (Manning's roughness, n = 0.014) with a diameter of 5 met used to convey a…

A: To find velocity of flow

Q: Determine maximum shear stress if maximum principal stress is 10 Mpa and minimum principal stress is…

A: Given data : Minimum principal stress=3 MPa Maximum principal stress=10 MPa Required : Maximum…

Q: 1. What is the relative stiffness of span AB, KAB? 0.375 I 0.125 I 2.667 I 0.250 I…

A: From the given question it is required to determine the distribution factor and relative stiffness…

Q: 1a) Figure Q1a shows two tubes made of the same material which are riveted together by 50 rivets of…

Q: -118. Determine the angle between cables AB a X A FY 1 m 0 0.75 m B O 1 m 3 m Probs. 2-117/118 OC…

Q: Design a simply support timber joist with span of 3.8 m for a domestic dwelling using timber of…

A: Given values: Clear span of joist, l = 3.8 m Bearing length = 100 mm Live load, wL = 0.763 KN/m…

Q: For the simply supported beam loaded as shown, determine the slope and deflection at point(D)…

Q: 1. Find the change in length and diameter of the 6061-T6 Aluminum thin-walled tube, with dimensions…

A: Given :

Q: Convert the 115/85 systolic/diastolic pressures given in millimeters of Hg to Pa .

A: To convert mmHg to Pa

Q: DETERMINE THE REACTIONS AND SHEAR & MOMENT DIAGRAM in MEMBER BCDE ONLY Let P=22

A: From the given question it is required to calculate the reactions, shear force and Bending Moment of…

Q: ) Determine the moment of inertia of the area shown in Fig. below about the x axis. L y L -X L = 40…

Q: Q1/Define the followings with drawing sketch: Precast building. lintel. Surface investigation. Pit…

Q: Explain what is meant by boundary and initial conditions.

A: Whenever differential equations are given from which a unique solution is to be derived, boundary…

Q: If the alum dose required to coagulate is 10 ppm, find out the amount of alum (in quintals) needed…

Q: A thin and weightless beam is supported by a pin connection at 4 and by a roller at B (see figure…

Q: The ??? diagram for a collagen fiber bundle from which a human tendon is composed is shown. σ (ksi)…

A: Solution: Given: Cross sectional area = 0.229 in2 length = 6.5 in Tension = 343.75 lb

Q: drag force on a smooth sphere

A: To find the expression for drag force acting on a smooth sphere with the following functions…

Q: A single-acting reciprocating pump discharges 0.018 m³ of water per second when running at 60 rpm.…

A: Given data- Discharge Q=0.018 m3/sN=60 rpmstroke length L=50 cm=0.50 mdiameter of piston d=22…

Q: Problem 4. A. Draw the F.B.D. of the frame shown in Fig. (4-A). B.Draw the F.B.D. of the figure…

A: Let,RA=vertical reaction at roller support in upward directionRB=vertical reaction at hinge support…

Q: Q2 The beam shown in Figure Q2 is loaded with a triangular distributed load from A to B, and a…

Q: Problem 2.63 The bolt is subjected to the force F, which has components acting along the z. y, z…

Q: Water is pumped from a supply reservoir to a ductile ron water transmission line. The high point of…

A: Given ;

Q: For the clevis connection shown in the figure, determine the maximum applied load P that can be…

A: Given :

Q: As shown in the accompanying figure, pipe M contains carbon tetrachloride of specific gravity 1.594…

Q: Explain Newton’s Laws.

A: Newton's laws of motion provide a scientific connection between the forces acting on a body and the…

Q: For the beam shown in Fig.(2), find the reaction forces at supports A and B respectively? 20 KN/m…

Q: 11. How would you determine the gap flow knowing that for the major drainage system design flow an…

A: Gap flow is defined as the the difference in runoff which results from a 1% Annual Exceedance…

Concept explainers

Soil Compaction Test

Soil compaction is the major area of geotechnical engineering. Soil is composed of multiple pores present on its surface, while the soil is mainly composed of gravel, sand, rocks, etc. The arrangement of these rocks and gravels is such that they build up voids (spaces) between them, which allows spaces for the roots of the plants and crops to spread and absorb the required amount of nutrients. Soil compaction is a major problem primarily caused by human activities, micro-organisms, and other multiple factors.

Question

a soil sample was determined to have a water
content of 8% and a degree of saturation of 42%.
After adding some water, the degree of saturation
was altered to 53%. take the specific gravity of the
soil solids to be 2.7. assuming no change in the
volume of the voids, determine the following
A. void ratio
B. water content%
C. bulk specific gravity of the mass of the sample in
the altered state.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(c) A sample of clay having a mass of 675 gm was coated with paraffin wax. The combined mass of the clay and the wax was found to be 682 gm. The volume was found by immersion in water as 345 ml. The sample was then broken to open. The water content and specific gravity of solids were found to be 15 % and 2.70 respectively. Calculate the bulk density of soil, its void ratio, and degree of saturation. Take specific gravity of wax as 0.89.
A dry sand is placed in a containerhaving a volume of 0.0089 cm3. The dry weight of the sample is 0.014 grams. Water is carefully added to the container so as not to be disturbthe condition of the sand. When the container is filled, the combined weight of the of soil plus water is 0.0174 grams. With this, find the void ratio, the porosity, the water content, the specific gravity thepertinent unit weights of the soil sample.
14. The soil sample in natural state having a volume of 0.0012 m³ weighs 1.73 kg. The degree of saturation being 45.6%. After drying in an oven, the final weight of the sample was 1.44 kg. a. Find the specific gravity of solid. b. Determine the void ratio.
16. In performing water content determination, the readability of the balance for specimen greater than 200 grams is ... A. 0.01 B. 0.001 C. 0.1 I D. 1 17. Which of the following clay mineral has a range of liquid limit between 55-120%? A. Illite B. Montmorillonite C. Kaolinite 18. True or False. Peat and highly organic soils can have water contents up to about 500%.
A sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density(ρ) of 2.05 g/cm3, a specific gravity of solids (Gs) of 2.67, and a moisture content (w) of 14.7%.First determine all entries in the phase diagram. Then determine the void ratio (e), the porosity(n), the degree of saturation (S), the dry density (ρd), the dry unit weight (γd), and the moistunit weight (γ).
The volume of the solids is 65cc. The wet weight of the soil is 198g having a saturation at 48% and the dried weight is 176g. Determine the following: a. Total volume of the sample, cc. b. Volume of the voids, cc. c. Air void ratio, %.
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquidity index of this clay? (Use Interpolation) Group of answer choices 0.895 0.96 1.08 0.90 Please answer this asap. For upvote. Thanks
A dry sand is placed in a containerhaving a volume of 0.0089 cm3. The dry weight of the sample is 0.011 grams. Water is carefully added to the container so as not to be disturbthe condition of the sand. When the container is filled, the combined weight of the of soil plus water is 0.0144 grams. With this, find the moisture content, moist unit weight, dry unit wait, void ratio, the porosity, and degree of saturation. for a saturated soil show that; ????=(?/?)(1+?/1+?)??
The total volume of a soil soecimen is 80,000 mm³ and it weighs 150 grams. The dry weight of the specimen is 130 grams and the density of the soil solids is 2680 Kg/m³. Find the following: a) The water content. b) Void Ratio. c) Porosity. d) Degree of saturation. e) Saturated unit weight. f) Dry unit weight.
Permeability tests were performed on a soil sample, under different void ratio and different temperatures and the following results were obtained. Test No. 1 2 Void ratio Temperature °C (e) 0.65 1.02 25° 40⁰ Estimate the coefficient of permeability at a temperature of 20°C for a voids ratio of 0.80. Given the following physical properties of water: At 20°C, n = 10.09 × 10+ and p„ = 0.998 g/cm³ At 25°C, n = 8.95 × 104 g sec/cm² and p k(cm/s) 0.4x10 1.9x10¹ At 40° C, n = 6.54 × 10 g sec/cm² and p 8 0.997 g/cm³ = 0.992 g/cm³
Permeability tests were performed on a soil sample, under different void ratio and different temperatures and the following results were obtained. Test No. 1 2 Void ratio (e) 0.65 1.02 Temperature °℃ 25° 40⁰ Estimate the coefficient of permeability at a temperature of 20°C for a voids ratio of 0.80. Given the following physical properties of water: At 20°C, n = 10.09 × 10+ and p„ = 0.998 g/cm³ At 25°C, n = 8.95 × 104 g sec/cm² and p k(cm/s) 0.4x10 1.9x10-¹ At 40° C, n = 6.54 × 10-¹ g sec/cm² and p $0.997 g/cm³ = = 0.992 g/cm³
A hydrometer test was conducted on the material passing sieve No, 200 and the results are listed in the table below, The results of sieve analysis on the soil showed that the percentage passing No. 4 was 90 % and that passing No. 200 was 20 %. Estimate the clay size fraction in the soil. Table : Results of hydrometer test diameter (mm) 0.0700 0.0400 0.0150 0.0020 % finer (combined) 19 finer 95 80 16 65 13 45 0.0010 30 6 Select one: