A solid brass shaft is loaded as shown below by two torques TB= 1100 Nm and TC= 400 Nm. The lengths of the two segments are LAB= 750 mm and LBC= 600 mm. For brass, G = 41 GPa. Neglect the effect of any stress concentrations. Determine the smallest diameters dAB and dBC for which an allowable shear stress of 60 MPa is not exceeded. Express each diameter as an integer in units of mm.

A solid brass shaft is loaded as shown below by two torques TB= 1100 Nm and TC= 400 Nm. The lengths of the two segments are LAB= 750 mm and LBC= 600 mm. For brass, G = 41 GPa. Neglect the effect of any stress concentrations. Determine the smallest diameters dAB and dBC for which an allowable shear stress of 60 MPa is not exceeded. Express each diameter as an integer in units of mm.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
An aluminium channel section is shown in the figure below: mm 1; mm mm li mm As indicated, the horizontal sides are of length / = 167 mm and thickness 1 - 1 mm while the vertical side is of length l2- 218 mm and thickness 12 - 3 mm. Determine the shear stress in the top side when it is subject to a pure torque of 20 Nm. You may assume that the factor ki may be taken as 0.333. Give your answer in N/mm² to three decimal places.
Given: A steel rod (A = 150mm^2) is stretched between two fixed points with a tensile load of 5000N at 20degree C. determine: a) the stress at -20 degree C b) at what temperature will the stress be zero *DRAW THE FBD: COMPLETE SOLUTION *USE 3 DEC PLACES
A steel bar has three segments with 600 mm long which is subjected to the differentloads as shown in Figure Q1(b). Take E=205 GPa. (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.(iii) Determine the length of the middle segment (BC) to have zero elongation ofbar.(iv) Determine the diameter of the segment CD to have zero elongation of the bar.
Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
Two steel tubes are joined at B by four pins (dp = 11 mm), as shown in the cross section a – a in the figure. The outer diameters of the tubes are dAB = 40 mm and dBC = 28 mm. The wall thicknesses are tAB = 6 mm and tBC = 7 mm. The yield stress in tension for the steel is (y = 200 MPa and the ultimate stress in tension is (U = 340 MPa. The corresponding yield and ultimate values in shear of the pine are 80 MPa and 140 MPa, respectively. Finally, the yield and ultimate values in bearing between the pins and the tubes are 260 MPa and 450 MPa, respectively. Assume that the factors of safety with respect to yield stress and ultimate stress are 4 and 5, respectively.Calculate the allowable tensile force Pallow considering tension in the tubes.Recompute the Pallow for shear in the pins.Finally, recompute Pallow for bearing between the pins and the tubes. What is the controlling value of P?
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
4. A piercing punch of a die assembly has a diameter of 20mm and will be used to punch in an aluminum plate with a thickness of 4mm. Knowing that the ultimate shear stress of the plate is 280 MPa, determine the force P required to punch through the plate. Punch Aluminum = 4 mm d=20 mm
PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN is applied. Note that a gap of 0.2 mm exist before the external load is Steel 280 mm applied and bars has equal distance with each other. Neglect the weight at the flat form. A = 1100 mm? E = 200 Gpa Steel Aluminum A = 2500 mm2 %3D E = 70 GPa %3D