A solid circular shaft 150 mm in diameter and 7 m long is subjected to a vertical load P = 14 kN and torque T = 50 kN-m bot acting at the midspan. The supports at both ends are pinned for vertical load and fixed for torque. Neglect the vertical shear. Determine the maximum torsional stress in the shaft. Select the correct response: 90.54 MPa 75.45 MPa 37.73 MPa 45.27 MPa

A solid circular shaft 150 mm in diameter and 7 m long is subjected to a vertical load P = 14 kN and torque T = 50 kN-m bot acting at the midspan. The supports at both ends are pinned for vertical load and fixed for torque. Neglect the vertical shear. Determine the maximum torsional stress in the shaft. Select the correct response: 90.54 MPa 75.45 MPa 37.73 MPa 45.27 MPa

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft. 43.33 MPa 35.01 MPa 13.12 MPa 22.11 MPa
NO. 4. The 150-kg bucket is suspended from end E of the frame. Determine the average normal stress in the 6- mm diameter wire CF and the 15-mm diameter short strut BD IN Figure 4.
A propped cantilever beam of length ? = 1 m, with an inner hinge at point B, carries a uniformly distributed load ?, as shown in Figure Q1 (a). The beam is made from a circular hollow section with an inner radius of ?? = 5 cm and a thickness of ? = 2 cm (refer to Figure Q1 (b)). The maximum allowable longitudinal stress of the beam is 150 N/mm2.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
Determine the magnitude of the maximum vertical force P (in kN) that can be applied to the bell crank so that the average normal stress developed in the 10-mm diameter rod CD, and the average shear stress developed in the 6-mm diameter double sheared pin B not exceed 175 MPa and 75 MPa, respectively
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm