A solid compound shaft consists of segment (1), which has a diameter of 40 mm, and segment (2), which has a diameter of 25 mm. The shaft is subjected to an axial compression load of P = 738 N-m and TC = 188 N-m and torques TB = 35 kN which act in the directions shown in Fig. 2. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. Te Fig. 2

A solid compound shaft consists of segment (1), which has a diameter of 40 mm, and segment (2), which has a diameter of 25 mm. The shaft is subjected to an axial compression load of P = 738 N-m and TC = 188 N-m and torques TB = 35 kN which act in the directions shown in Fig. 2. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. Te Fig. 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is subjected to a tensile axial load of P = 5 kips and torques TA = 12 kip·in. and TB = 34 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip-in. and TB = 34 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
For the loaded beam shown in Figure Q6 below, consider section M-M and determine the following : 6.1.The maximum shear stress in that section 6.1.The shearing stress at point P
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P = 40 kN. Follow the sign convention. a) Although it is not very accurate, use the shear formula to determine the shear stress developed at point A b) Determine the principal stress σ1 at point A c) Determine the principal stress σ2 at point A
A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft. 43.33 MPa 35.01 MPa 13.12 MPa 22.11 MPa
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a length of 3 m. The pipe is fixed at the bottom and free on top and is subjected to a torque of 25 Kn-m and lateral force 39 kN. G = 78 GPa. Calculate the maximum angle of twist in degrees, maximum shear stress due to torque, maximum shear stress due to lateral force, and maximum flexural stress.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
The 160-mm-diameter solid shaft is supported by bearings at A and E. Determine the maximum shear stress developed in each segment of the shaft.