A solid conical bar of circular cross-section is suspended vertically as shown in the figure. The diameter of the bar at the base D equals 100 mm and its length L, is 0.5 m. if E= 200GN/m² and its weight per unit volume is 80 kN/m³, the elongation of the bar under self-weight is D

A solid conical bar of circular cross-section is suspended vertically as shown in the figure. The diameter of the bar at the base D equals 100 mm and its length L, is 0.5 m. if E= 200GN/m² and its weight per unit volume is 80 kN/m³, the elongation of the bar under self-weight is D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin cylinder 200mm internal diameter, 3mm thick has its ends closed with rigid plates. The cylinder is then filled with water. When an external axial pull of 60KN is applied to the ends then the water pressure is observed to fall by 0.1N/mm2.Determine the value of Poisson’s ratio. Take E = 170,000N/mm2, K=2000N/mm2.
The modulus of elasticity of the cantilever beam shown in the figure = 210.000 MPa and the length L = 5 m. Since q = 10 kN/m and 1=1,5x10-6 mm* end B collapses and calculate the rotation. 9 1 B L
A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P = 50 kN. The elongation of the rod is 8 = 2.00 mm, and its %3D diameter becomes d' = 19.99635 mm. Determine the modulus of elasticity and the modulus of rigidity of the material. Assume that the material does not yield.
A solid circular rod that is 800 mm long and 30 mm in diameter is subjected to an axial force of P = 60 kN. The elongation of the rod is 6 = 4.00 mm, and its diameter becomes d' = 29.99550 mm. Determine the modulus of elasticity and the modulus of rigidity of the material. Assume that the material does not yield. P = 60 kN 800 mm 30 mm P = 60 kN
A beam with a cross section shown as the shaded area below is subjected to an internal bending moment M 100 Nm. (1) Determine the maximal tensile stress and compressive stress developed in this cross section. (2) Determine the orientation of the neutral axis. 100mm 80mm 30° 60mm 80mm M = 100 N·m X Answer: (1) σ= 1.762 MPa; (2) α = 39.99⁰
b b/2 Figure Q.4 shows a dam retaining a water reser- voir of uniform density p. The dam has uniform width, L, in the direction into the page. Use the information provided in Figure Q.4 to find the load, F = Fri - F,k, the water applies to the dam's face, relative to the (x, y, z) axis shown (y is directed into the page). Find also the corre- sponding point of action, xp = x,i + ypj + zpk. H/3 Figure Q.4.
AThe stress tensor at a point is given by the following = 30 oz = 20 MPa, Txy 20 MPa, Tyz 40 txz = 30 GX = 40 oy = MPа %3D calculate stress invariant and prove that it is unchanged when the system is rotated by 60 degree anticlockwise about x3.
A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P = 50 kN. The elongation of the rod is δ = 1.40 mm, and its diameter becomes δ′ =19.9837 mm. Determine the modulus of elasticity and the modulus of rigidity (both in GPa) of the material. Assume that the material does not yield. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
A segment of a generator shaft is subjected to a torque T and an axial force P, as shown in the figure. The shaft is hollow (outer diameter d, = 295 mm and inner diameter d, = 250 mm) and delivers 1,700 kW at 4.0 Hz. If the compressive force P = 600 kN, what are the maximum tensile, compressive, and shear stresses in the shaft? (Enter the magnitudes in MPa. Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain e resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) maximum tensile stress 676 X MPa maximum compressive stress 31461.087 X MPa maximum shear stress 277.126 X MPa Construct a clear sketch of Mohr's circle for this problem, and construct a sketch of the stresses on properly oriented elements for your above solutions, clearly indicating the orientation wrt the base x-y coordinate system (as demonstrated in the lectures). Submit…
A cylindrical bar of 600mm length is subjected to a tensile load of 80 kN along the axis. G = 80 GPa. The change in volume of the cylinder is 72 mm³. The poisson's ratio of the cylinder material is
A machine of mass m = 500 kg is mounted on a simply supported steel beam of length = 2 m and having a rectangular cross section (depth = 0.1 m and width = 1.2 m) and Young’s modulus E= 2.06 x 1011 N/m^2. To reduce the vertical deflection of the beam by 25% of its original value, a spring of stiffness k is attached at midspan. -What is the total displacement of the system? -What is the stiffness of the spring that will limit the system displacement? -What is the total spring stiffness equivalent of the system? -What is the arrangement of the springs in the system? -What is the original deflection of the beam? -What is the beam’s spring stiffness? -What is the area moment of inertia of the beam?
The structure is loaded as shown in the figure. Determine the internal axial force, shear force and bending moment at point C. Also, calculate the internal bending moment at D. 26 kN 7 kN/ m 0.7 m 0.6 m 0.8 m 12 kN/ m 0.4 m show free body diagram Find: Vc = ? kN PC = ? kN MC = ? kN-m MD = ? kN-m