Solve it correctly please. I will rate and review accordingly. A solid round steel rod with Sy = 350 MPa is 1,130 mm long and 67 mm in diameter.With a safety factor of 4, what axial compressive load (in kN) can be applied if bothends are built in, as shown in the figure below?%3DLLe

Given data: Sy=350MpaL=1.13mD=67mmFOS=4

Answered: A solid round steel rod with Sy = 350…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the 12 kn m torque is applied to the free end of the 6-m steel shaft. the angle of rotation of the shaft is to be limited to 3 degrees. find the diameter d of the smallest shaft that can be used. What will be the maximum shear stress in the shaft? Use G=83GPa for steel
The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 , and if this section is under a bending moment of 22 kN m, please calculate the normal stress at Point B: ____ MPa. Calculate your answer to 1 decimal place.
A beam is fabricated by bending and welding a 6mm thick plate to form a hollow rectangular box section 100 mm overall width and 160 mm overall depth. If the safe permissible bending stress is 165 N/mm^2, calculate the moment of resistance of the section. [Ans.: 21.36 KNm]
A stepped shaft is as in Figure 5-13. The AB part is aluminum (G = 28GPA) and the BC part is steel (G= 84GPA). The aluminum part has a solid circular section with a diameter of 45 mm and the steel part has a circular head section with an outer diameter of 60 mm and an inner diameter of 30 mm. Find the maximum shear stress in each material and the torsion angle at B at which the torsion moment of 4000 N.m is applied. A and C terminals are rigidly connected.
Q2: For the shaft shown in Figure 2, find the maximum shearing stress in the Aluminum and the steel and the total angle of Twist. Use G aluminum =28 GPa. G steel =83 GPa. Use the data in Table 2 Figure 2
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression o is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
A cast iron beam is of T-Section as shown in figure 5.1. The beam is simply supported on a span of 8m. The beam carries a uniformly distributed load of 1.5kN/m length on the entire span. a) Determine the maximum tensile and maximum comparative stress. please show working in details.
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
1. A thin walled cylindrical shell has an internal diameter of 2 m. And is fabricated from plates 20 mm. Thick. Calculate the safe pressure in the shell if the tensile strength of the Plate is 400 kN/mm2 and the factor of safety is 6. unit of answer is in n/mm^@ 2. Determine the force (lbs) required to punch a ½ inch hole on a 3/8 thick plate if the ultimate shearing strength of the plate is 50,000 psi.
A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? α=11.7x〖10〗^(-6)/°C and E = 200GPa. See figure 06
Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A solid round steel rod with Sy = 350 MPa is 1,130 mm long and 67 mm in diameter. With a safety factor of 4, what axial compressive load (in kN) can be applied if both ends are built in, as shown in the figure below? L Le