Answered: A solid steel shaft, 1.5 feet in…

A solid steel shaft, 1.5 feet in diameter and 30 feet long, is rotating at 50 RPM and transmits a torque of 150,000 ft-lb. What horsepower is being transmitted?

Electrical Transformers and Rotating Machines

4th Edition

ISBN:9781305494817

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Motor Nameplate Data

Section: Chapter Questions

Problem 6RQ: A motor develops 225 ft-lb of torque at 860 RPM. What is the horsepower output of the motor?

See similar textbooks

Related questions

Q: A torsion dynamometer is fitted on turbine shaft to measure the angle of twist. The shaft twist 1.6°…

A: A torsion dynamometer is installed on the turbine shaft to measure the angle of twist, as we know.At…

Q: A hollow shaft 3 feet long and with radii 1.5 in and 2 in is used to transmit power from an 8 HP…

Q: 10N 1m 1 m 1 m 1m c 1 m 5N 1 m E 10N + 10N 1 m 1 m 20N 5N 10N Find the summation of torque / moments…

A: clockwise moment is taken as +ve Moment at B, Mb =(5*3)+(10*2)+(10*1)+(20/2)-(10*1)-(5*2)-(10*2) =…

Q: Compute the torque (Nm) on a shaft transmitting 750 W of power while rotating at 1750 revolutions…

A: Given data: The power transmitted through a shaft can be expressed as,

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

Q: Determine the torque in in-lb received by the motor shaft running at 4250 rpm, transmitting 11 Bhp.

A: To find: The torque in lb‐in. Given: The speed of shaft is 4250 rpm. The power transmitted through…

Q: (b) A hollow shaft, having an inside diameter of 60% of its outer diameter, is to replace a solid…

A: It is given that the material, power transmitted and the speed of the both shafts is same. Torque…

Q: A torsion dynamometer is fitted on turbine shaft to measure the angle of twist. It is observed that…

Q: A hollow bronze shaft of 75 mm outside diameter and 12.5 mm thick is coaxial with a solid steel…

Q: .Assume the shafts are straight, the material is homogeneous and the shafts are made of the same…

A: Solution:- Calculation:- 1. for equal stress 16 Troundπd3 =4.8Tsquared3Tsquare = Tround164.8π…

Q: Question O Answered step-by-step A solid transmission shaft is 3.5 inch in diameter. It is desired…

Q: A 9-in solid shaft has the same cross-sectional area as the hollow shaft of the same material with…

A: Given Data The diameter of the solid shaft is: D=9 in The inner diameter of the hollow shaft is:…

Q: The torque of a steel shaft transmitting 20 kW at 320 rpm is

A: Power transmitted by the steel shaft, P = 20 kW = 20*103 W Revolutions, N = 320 rpm

Q: What power can be transmitted by a solid shaft with torque 120 Nm and at frequency of 14 Hz?

A: Given Data T=120 Nm f=14 Hz

Q: A solid steel shaft 3 m lang is stressed to 65 MPa when twisted through 2º. A. Given that G = 83…

A: Modulus of rigidity: It is the ratio of shear stress to shear strain. Shear stress: The ratio of…

Q: A solid steel shaft is stressed at 100 Mpa when twisted through 6 degrees. Compute the Diameter of…

A: Given:ζ=100 MPaθ=6°f=25 HzL=15 mG=83 GPa

Q: What is the diameter of a solid shaft that will not twist through more than 1.5° in a 200 cm length…

Q: A solid and a hollow shaft are made of same material. The diameter of the solid shaft is 300 mm and…

Q: The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner…

A: Find the second moment of area about diametric axis.

Q: A torsion dynamometer is fitted on turbine shaft to measure the angle of twist. The shaft twist 1.6°…

A: Torsion dynamo meters are machine components that are often mounted between the motor and the driven…

Q: D 500 lb-ft 12 in 1 in. B

A: Given data A 500lb-ft torque is applied Required What is the effects if we change the torque…

Q: Two short shafts having identical diameter of 38.1mm and rotating at 400 rpm are connected by a…

A: Given: d =38.1 mm N = 400 rpm Correct answer: 0.633 kN-m

Q: (11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a…

A: Given data, Diameter of the diamond blade, D = 120 cm = 1.2 m Peripheral linear speed of the blade,…

Q: A solid circular steel shaft having an outside diameter of 2.00 in. is subjected to a pure torque of…

Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…

A: Given, Length of shaft = L = 1 m Power transmitted = P = 30 kW = 30 x 103 W Shaft RPM = 700 rpm…

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: Given: The center distance between shafts is 1.67 ft. The speed of the input shaft is 350 rpm. The…

Q: Q23: Assume that the solid steel shaft (2) must not twist more than 0.075 rad in a 5-ft length.…

Q: Q1 Calculate the motor power required to bend a beam of 3m the motor is equipped by two poles.

A: Given Data : Bend Length(L)= 3 m Force(F)=10 N Number of poles(P)=2

Q: 1. Four cylinders rlling in opposite directions has a speed ratio of A:B:C:D = 5:3:1:4. If center…

Q: What is the diameter of line shaft that transmit 180 kW at 25 rps?

Q: The outside diameter of a hollow shaft that is twice its inside diameter the ratio of its torque…

A: This question is related to the solid shaft and hollow shaft. For the solid shaft, Shear stress…

Q: A motor with a torque of 37.26N/m and a speed of 120°/sec rotates a robotic arm that consists of two…

A: Given: The torque, T = 37.26 N.m The speed, w = 120o/s = 2.093 rad/s The diameter of worm gear, d =…

Q: 45. A geared turbine unit delivers 18,500 kW at the bull gear coupling at full power with a…

A: Find the mechanical losses at 35 km/hr.

Q: Explain about derivation of shaft strength...?

A: Derivation of shaft strength ;

Q: A solid steel shaft transmits 50 KW of power at the frequency of (50/ π) Hz. The initial torque…

A: Data given- P = 50 kW f = 50 / π

Q: A solid shaft 15 meters long is stressed to 85 MPa when twisted through 6 degrees. If G = 83 GPa.…

Q: 11.5 (A/B). Two shafts, one of steel and the other of phosphor bronze, are of the same length and…

A: Both steel shaft and phosphor bronze shafts are having same length. Hence, Ls= Lpb. Both steel shaft…

Q: A solid shaft of 250 mm diameter has the same cross-section area as the hollow shaft of the same…

A: Given data: The diameter of the solid shaft, ds = 250 mm. The outside diameter of the hollow shaft,…

Q: An internal combustion engine delivers 394 Hp, while exerting a torque of 164 Ibf ft. Determine the…

A: Given data:

Q: 30mm diameter copper (G-4S GPa) shaft is transmitting power at 1000 rpm. The twisting angle should…

Q: 1. Four cylinders rolling in opposite directions has a speed ratio of A:B.C:D = 5:3:1:4. If center…

Q: The outside diameter of a hollow shaft that is twice its inside diameter .what is the ratio of its…

A: Given:Outside diameter of a hollow shaft is twice its inside diameter, D=2dD=outside…

Q: A solid steel shaft 4.5 m long is stressed at 75 MPa when twisted through 4.5°. What power can be…

A: Given: Twisting angle, θ = 4.5° = 4.5°π180° Stress, τmax = 75 MPa Length, L = 4.5 m = 4500 mm G =…

Q: A solid shaft 5 meters long is stressed to 55 MPa when twisted through 4 degrees. If G = 83 GPa.…

Q: A motor running at 1800 rpm transmits 10 KW of power through a 25 mm diameter shaft 1.2 m long. What…

A: It is required to determine angle of twist in the shaft

Q: Calculate the torque which a 11/11 shaft of 100 mm Radius can safely transmit, if the shear stress…

A: Given data: Radius of the shaft (R) = 100 mm Shear stress τ=50 N/mm2 Need to determine the torque…

Q: A hollow steel shaft is stressed to 35 MPa by a torque of 200000NM. Determine the outside diameter…

Q: What is the max shear stress on a shaft under a torque of T = 54.167 lb-ft having a diameter of 0.75…

A: Given:T=54.167 lb.ftd=0.75 in

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

A solid steel shaft, 1.5 feet in diameter and 30 feet long, is rotating at 50 RPM and
transmits a torque of 150,000 ft-lb. What horsepower is being transmitted?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What power can be transmitted by a solid shaft with torque 120 Nm and at frequency of 14 Hz?
The outside diameter of a hollow shaft that is twice its inside diameter .what is the ratio of its torque carrying capacity to that of a solid shaft of the same material and the same outside diameter?
1.A rotor has an inner radius of 10.0 cm and an outer radius of 25.0 cm. It is fixed to a frictionless axle that goes through its center. The moment of inertia (I) of the rotor is 0.0235 kg m2. A set of 5 constant forces act on the rotor, as shown in the diagram below. (a) Find the net torque acting on the rotor, in units of Nm. Be sure to give both the magnitude and direction. (b) Find the angular acceleration of the rotor, in units of rad/s2. Give both the magnitude and direction. (c) Assuming it starts from rest at t = 0, how long does it take for the rotor to reach an angular speed of 565 revolutions pre minute (rpm)? Give your answer in seconds. (d) At t = 2.50 seconds, how many complete revolutions will the rotor have made?
Shaft A with 9 inches diameter cylinder running at 190 rpm is connected to shaft B by means of 24 inches diameter cylinder. Another cylinder on shaft B, 14 inches in diameter, is connected to 10 inches diameter cylinder on shaft C. Find the speed of shaft C. SPEED OF SHAFT C:
An industrial fan running at 600 rpm is driven by a 25-kW, 960 rpm, induction motor. The pulley mounted on the motor shaft is 270 mm. Center to center distance is 1.5 meters and use f = 0.35. Determine the minimum angle of wrap in rad.
The maximum torque transmitted by the shaft of an industrial machine is 1.15 times the mean torque. The value of maximum torque transmitted is 135 Nm. Find the power transmitted by the shaft in W when the speed of rotation is 427 rpm. The power transmitted in W??
A pulley 600 mm. in diameter transmits 40 kW at 500 rpm. The arc of contact between the belt and pulley is 144° having a center distance of 1100 mm. Determine: (a) diameter of the driven pulley for open belt drive, (b) speed of the driven pulley, and (c) belt length for open belt connection.
A motor, operating clockwise at 1.498 rpm, is coupled through a belt drive to rotate an industrial exhaust fan. The diameter of the motor sheave is 8 in. and the sheave on the fan is 10 in. Determine the speed of the driven sheave
The geometries of a solid round shaft and a solid square shaft of the same size (circle diameter equal to side of square) are given. Compare a) the torque transmitting strength, b) the weight, and c) the ratio of strength to weight of the two shafts .Assume the shafts are straight, the material is homogeneous and the shafts are made of the same material
Driver Pulley 1 is 10” in diameter, runs at 1200 RPM, and supplies 2.5 ft-lbs of torque. Pulley 2 (driven) is 32” in diameter. What is the output torque of Pulley 2? What is the output speed of Pulley 2?
What is the indicated horsepower of a single cylinder four-stroke gasoline engine if the engine speed is 1000 rpm? Assuming the mean effective pressure of 0.55 MPa. The diameter and piston stroke is 110mm and 140mm
A solid steel shaft transmits 50 KW of power at the frequency of (50/ π) Hz. The initial torque needed in the shaft is A) 812 N-m B) 678 N-m C) 541 N-m D) 500 N-m