A solid steel shaft is loaded as shown in the figure. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 94 MPa and the angle of rotation at the free end is not to exceed 3 deg. If the stress defines the size of the shaft, what is the corresponding angle of rotation at the end when the required diameter is used of if the angle of rotation defines the size the size of the shaft, what is the corresponding stress when the required diameter is used?

A solid steel shaft is loaded as shown in the figure. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 94 MPa and the angle of rotation at the free end is not to exceed 3 deg. If the stress defines the size of the shaft, what is the corresponding angle of rotation at the end when the required diameter is used of if the angle of rotation defines the size the size of the shaft, what is the corresponding stress when the required diameter is used?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate. Answer a and b please
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
The steel shaft of a socket wrench has a diameter of 8.0 mm. and a length of 200mm (see figure). If the allowable stress in shear is 60 MPa, what is the maximum permissible torque Tmax that may be exerted with the wrench? Through what angle f (in degrees) will the shaft twist under the action of the maximum torque? (Assume G=78 GPa and disregard any bending of the shaft.)
A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 39 ksi, determine the minimum force P (in kips rounded to the nearest tenths) required to punch the slot. Assume d = 0.75 in. and a = 4.00 in.
Q#1: A block is shown in figure. Consider a compressive load is applied (one at a time) on all corners (A, B, C and D) of the block. This will cause each corner to be in a different state of stress under the action of load at different location. Discuss the effect of load on each corner under changing load locations. It is mandatory to consider the effects of direct stresses and bending stresses. (1
Problem # 4: The tank shown is fabricated from steel plate. Determine the minimum thickness of plate which may be used if the stress is limited to 42 MPa and the internal pressure is 1.5 MPa. USING BOTH TANGENTIAL AND LONGITUDINAL STRESS FORMULA.
The T-beam given in the figure is made of two 250 mm x 25 mm section wooden planks. Wooden planks as It was brought together by being nailed like. a) Draw the shear and moment diagrams (influence lines) of the beam. The greatest shear and bending force acting on the beam Determine where and where the moment occurs. b) If the permissible safe axial stress σsecurity in the beam = 10 MPa and the safe shear stress τ = 0.7 MPa, calculate whether this beam is safe under loading. c) When the planks are fixed to each other, if the force that a nail can safely carry is 400 N, between the nails Find the highest distance about. Note: There is a fixed bearing at the A point and a sliding bearing at the C point.
A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 27 ksi, determine the minimum force P required to punch the slot. Assume d = 1.00 in. and a = 3.50 in.
Given a rectangular hollow box with outer dimensions 125mm x 85mm and constant thickness of 10mm has an ultimate stress of 415 MPa. Modulus of Elasticity of 110 GPa. a. Determine the bending moment M for which the factor of safety will be 2.50. b. Determine the corresponding radius of curvature of the section.
A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 0.9 GPa. Each bar has a cross-sectional area of 1050 mm2. Using L = 395 mm and Δ = 7.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? [Answer: P = 67.0 kN]