A specimen is subjected to a tri-axial test. The soil specimen is cohesionless. If the shear stress that cause failure is 3oo kPa and the normal stress at failure is only 475 kPa. 1. Determine the angle of shearing resistance. 2.Determine the angle that the failure plane measured from the major principal plane 3.Determine the maximum principal stress at which failure is expected to occur

A specimen is subjected to a tri-axial test. The soil specimen is cohesionless. If the shear stress that cause failure is 3oo kPa and the normal stress at failure is only 475 kPa. 1. Determine the angle of shearing resistance. 2.Determine the angle that the failure plane measured from the major principal plane 3.Determine the maximum principal stress at which failure is expected to occur

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.10P

See similar textbooks

Similar questions

3. In a drained tri-axial test, a specimen is confined under pressure and axially loaded until failure. The failure conditions of the specimen are analyzed for shear strength. What is the value of the minor principle stress? Half the value of the major principle stress Twice the value of the major principle stress . The same as the confining pressure The same as the cohesion value ● ● ●
A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a soild circular bar. a. Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b. If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
At failure, the major and minor principal stresses on a triaxial test are 200 kPa and 110 kPa respectively. If the porewater pressure at failure is 25 kPa... Q: What is the sine of the angle of shearing resistance of the soil? Round off your answer to two decimal places.
2- A three-axis compression test has been performed on the clay sample, which has been comprehensively and normally strengthened to a stress of 300 kPa and a specific volume of 200. The values of q and volumetric strain are measured at axial strain of 0, 2 and percent (rupture). The value of N is equal to 300 and Landa is equal to 0.2. Draw a diagram of all- round stress on the initial all-round stress in terms of slicing on the initial all-round stress:.
8. A cohesionless (c' = 0 kPa) soil specimen was subjected to a consolidated-undrained triaxial test. The total stress path, the deviator stress, and the pwp are shown in the figures below. No scale is intended in the figure of the stress path. a. Determine o'₁ and 0's at failure. [o'₁ = 345 kPa, o's= 140 kPa] b. Determine the effective friction angle (') of the soil. [$' = 25°] C. Determine the 'A' pore water pressure parameter at failure. [A+ = 0.29] 250 -Deviator Stress q (kPa), 200 150 100 50 200 p (kPa) Deviator stress or PW/P (kPa) 5 10 Vertical strain (%) ---PWP 15 20
In the discussion of Von-Mises criterion, how different is the description of J2 when compared to the Von-Mises stress?
10-14. The state plane stress in a mass of dense cohesionless sand is described by the following stresses: Normal stress on horizontal plane Normal stress on vertical plane = 200 kPa Shear stress on horizontal and vertical planes 370 kPa 80 kPa %3! Determine by means of the Mohr circle the magnitude and direc- tion of the principal stresses. Is this state of stress safe against failure? (After A. Casagrande.)
In a direct shear test on a specimen of cohesionless soil (sand), the vertical normal stress on the specimen is 210 kPa and the horizontal shear stress at failure is 135 kPa. You may assume the uniform stress distribution within the failure zone. a) determine the magnitude and direction of the principal stresses at failure using a Mohr's circle b) briefly explain whether it's possible to determine the magnitude and direction of the principal stresses when the material is not failed.
The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi compression and 25 psi, respectively. On an orthogonal plane the stresses are 40 psi compression and 25 psi. (a) Draw the Mohr's circle for this stress condition. (b) What are the principal stresses?
1. What is the rock’s maximum principal stress? 2. What is the rock’s minimum principal stress? 3. Normal stress at Failure Plane A-B 4. Shear stress at Failure Plane A-B
Also, Determine the magnitude of the minor principal stresses (in kPa). Determine the magnitude of the major principal stresses (in kPa). Determine the magnitude of the maximum shear stress (in kPa). Determine the angle from principal plane to the maximum shear stress at the Mohr's Circle. Determine the orientation of the angle (from principal plane) should the specimen be rotated or inclined to achieve the maximum shear stress. At what angle (from horizontal; assume counter-clockwise rotation) should the specimen be rotated or inclined so that it will not be subjected to shear stress? Determine the normal stresses (in kPa) on plane AB. Determine the shear stresses (in kPa) on plane AB.