A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: 0 = i ksi

A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: 0 = i ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Related questions

Q: 5. For the overdamped oscillations, the displacement x(t) is expressed by the following x(t)-e-t [A…

A: Given data: x(t) = e-βt A eωt + B e-ωtWe have to find it's expression in terms of hyperbolic…

Q: An ideal reheat Rankine cycle uses water as the working fluid. Steam enters the high-pressure…

A: Given:P1=10 MPaT1=500°CP2=2.5 MPaT3=500°CP4=10 KPa

Q: A- There are good and bad effects of mechanical vibrations. Give five examples of the bad effects of…

A: Solution.jpg

Q: A 2600-lb car is moving at a speed of 66 mph when the brakes are fully applied, causing all four…

Q: A one-dimensional plane wall is exposed to convective and radiative conditions at x = 0. The ambient…

Q: In the structure shown, an 8-mm-diameter pin is used at A, and two pins are used at B and D. Knowing…

A: Given data: pin A diameter = dA = 8 mm Ultimate shearing stress at pin A = 100 MPa = 100 n/mm2

Q: A 10,000-kW turbogenerator operating at rated capacity receives 52,000 kg/h of steam at 2.90 MPa and…

Q: Figure 1 shows a compressor running on refrigerant-134a with a constant mass flow rate of 6 kg/s.…

Q: A rectangular concrete channel 4.5 m wide is carrying water. At an upstream point, the depth of…

A: Given: Wide, b= 4.5 m Depth at upstream , d1 = 1.5m Depth at downstream,d2 = 1.17 m Length, L=…

Q: Superheated steam at 575ºC is routed from a boiler to the turbine of an electric power plant through…

A: Given data: Tis = surface temperature in the inside of the steel tube = 575 deg.C + 273 = 848 K Tos…

Q: An alloy system consists of two metals A&B which are soluble in each other in all proportions in the…

A: The phase diagram and the corresponding point for the given wt% of A and B is shown below.

Q: Q2/ The torques shown, in Fig. 2, are exerted on pulleys A and B. Knowing that the shafts are solid…

Q: Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled…

A: Solution.jpg

Q: (a) i) Consider an ideal gas at a given state that expands to a fixed final volume. In the first…

Q: Water flows through a pipe at 130 L/s that changes gradually in diameter from 154mm at point A to…

Q: Explain briefly the function of steam turbine in a steam power plant with the aid of a simple…

A: The steam turbine is a component of a steam power plant. A steam turbine is a type of heat engine…

Q: Using the Component method, determine the magnitude and direction of the resultant and the…

Q: A harmonic motion has a frequency of 30 cycle/second and its maximum velocity is 10 m/s. Determine…

A: Given:f=30 hzvmax=10 m/s

Q: Q/A rigid type flange coupling are connected two shafts made of plain carbon steel. The shafts are…

A: Given Shear stress = 60 MPa Power, P = 25 kW Speed, N = 500 rpm Find Diameter, d

Q: ) why balancing of reciprocating masses is necessary for machine with any two oil and gas plant…

A: Introduction: Reciprocating mass: A weighted item that spins or moves is referred to as a…

Q: The 3D model can be reflected about OXY plane OXY, YZ and XZ planes O YZ plane XY and XZ planes O…

A: Reflection of object is like mirror of an object. Reflection transformation matrix is used to do the…

Q: 2. A steam power plant uses the ideal Regenarative Rankine cycle with single open feedwater heater…

A: Given that: For a regenerative Rankine cycle, high pressure turbine inlet pressure and temperature…

Q: نقطة = * Types of gases that are using in the Pig iron making are Air and oxygen CO CO2 O C04

A: Solution.jpg

Q: 4. A pipe carries oil of density 800 kg/m³. At a given point (1) the pipe has a bore area of 0.005…

Q: In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final)…

Q: 12. The frequency of a damped harmonic oscillator is three-quarters of the frequency of the same…

Q: Air flow through along duct of constant area at (0.15Kg/sec), a short section of the duct is cooled.…

Q: A light shaft supported in bearings at its ends carries a rotor of mass m at its mid span. When…

Q: In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final)…

A: For solution refer below images.

Q: Cl 3. F (9001) O 0 P d DO

Q: Prob. 2.2-6. The three-part axially loaded member in Fig. P2.2-6 consists of a tubular segment (1)…

Q: 2) If the under-damped spring mass system shown at right is subject to the force F(t)= Fe (e is the…

Q: HOTE 7 LIT UAD CAME 1.9 A mass of gas at an initial pressure of 28 bar, and with an internal energy…

Q: During a drilling operation, the small robotic device is subjected to an (800 N) force as shown.…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: 5. When the harmonic oscillator depends on the direction and its restoring force is independent on…

A: Solution.jpg

Q: What is the measure of absolute pressure due to the weight of air molecules above a certain height…

A: Given = multiple choice question is given

Q: Q3: For the stresses at the point shown, find the followings: 1- The maximum shear stress. 2- The…

Q: A skier is pulled by a rope exerting a horizontal force T=0.8 kN at a distance h= 39 cm above the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: لنقطة To concentrate the copper In Copper production process, flotation tanks or bedding bins are…

A: Given

Q: Calculate the heat (q) and the work (w) in Joules, which the system exchanges with return process in…

A: Given:Ti=300 KTf=500 Km=2 gCp=43.0 J/g.Kcv=0.0346 J/g.K

Q: Bohar model Gizmo answer keys

A: Niels Bohr proposed in 1913 that the unique spectral lines produced by various elements were related…

Q: BRIEFLY EXPLAIN CONDUCTION, CONVECTION AND RADIATION. GIVE EXAMPLES/SITUATIONS

A: To find : short explanation conduction, convection and radiation with examples

Q: Determine the maximum flow through a 1.2-m diameter concrete culvert which is laid on a slope of…

Q: Q4/A/ The tension specimen contains has original length L. -100 mm as a result of the tension its…

A: Given:Lo=100 mmLf=120 mm

Q: The following data apply to a twin-spool turbofan engine, with the fan driven by the LP turbine and…

Q: 1. Consider the system with T-m(²+²6² +22) and U = mgz where z=cr²,9= wt, by using the Lagrangian…

Q: 11. A particle is released from the rest (y=0) and falls under the influence of gravity with air…

Q: PROBLEM 3 Mechanical system consists of: body 1 of mass mm; body 3 - two-stage disk of mass my-2m,…

A: “Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: Problem 2 The are studying a planetary gear system. The outer gear ring is stationary. A motor that…

Question

A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46,
determine the stresses in the balloon. Assume the stress-strain behavior is linear.
Answer: 0 = i
ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The cylindrical tank with a spherical end cap has an outer radius of 2 m and a wall thickness of 50 mm. If the tank is pressurized to 3.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the end cap. (Show free body diagram and complete solution)
Find the Principal Stresses on the tube below given the forces in the X,Y and Z axis shown below: Radius: R2=5mm R1=4mm and τxy= 0.1 Pa
The wire BC has a diameter of 3.4 mm and the material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle at D if the pull at the grip is slowly increased and reaches a magnitude of (a) P = 2250 N, (b) P = 3000 N.
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the endcap.
A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0 = 160 ×10-6 m/m, ϵ60 = -220 ×10-6 m/m and ϵ120 = 360 ×10-6 m/m. Using E = 10 ×106 psi and v = 0.3, Determine the principle stresses and the maximum in-plane shear stress.