A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown. We know that the spacing be- tween the nails is s=50 mm and that the allowable shearing force in each nail is 300 N, calculate (a) the largest allowable vertical shear in the beam, (b) the corresponding maximum the beam 20 mm- 80 mm 20 mm 120 mm

A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown. We know that the spacing be- tween the nails is s=50 mm and that the allowable shearing force in each nail is 300 N, calculate (a) the largest allowable vertical shear in the beam, (b) the corresponding maximum the beam 20 mm- 80 mm 20 mm 120 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
A simply supported wood beam with overhang is subjected to uniformly distributed load q. * Inserted Photo * The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm.Determine the maximum permissible value q if the allowable bending stress is ?all = 11.2 MPa, and the allowable shear stress is ?all = 1.50 MPa. (Enter the magnitude in kN/m.)
1What is the value of shear at B? 2At what distance from A is zero shear located? 3What is the value of bending moment at C? 4What is the maximum shear stress of the beam? 5What is the maximum bending stress of the beam?
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.65x105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?
The cantilever beam shown has the following dimensions: a = 300 mm; b = c = 400 mm; d = g = 24 mm; e = g = 96. The loads are ωo = 2 kN/m and P = 3 kN. Determine the maximum bendingstress and the maximum shear stress in the beam.
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the cross section shown: a = 30mm, bf = 69mm, tw = tf = 4mm, d=72 mm, determine:(a) the shear stress Th at point H, which is located 30 mm above the bottom surface of the tee shape(b) the maximum horizontal shear stress Tmax in the tee shape
The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 75 MPa. If P = 8000 N, what is the minimum shearing stress developed in the rivet.
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. Determine the following: a. maximum value of w without exceeding the permissible flexure stress of 10MPa. b. maximum value of w without exceeding the permissible shear stress of 1.2MPa. c. maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.Please show your clean and complete solution. Thanks
a.If the beam cross section is a rectangle with a breadth and depth of 6 in and 8 in respectively, what is the bending and shearingstress? b. If the beam cross section is circular with diameter of 8 in, determine the shear stress. c. Compute for the midspan value of EIy in lb.ft3 d.Considering the following design conditions for the beam:Allowable bending stress: 20000 psiAllowable shear stress: 10000 psiMaximum allowable deflection: L/360 Determine the safe dimensions depth h and breadth b in inches if h = 2b tnx.