A square threaded bolt of mean diameter 24 mm and pitch 5 mm is tightened by screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of friction for the nut and bolt is 0.1 and for the nut and bearing surfaces 0.16, find the force required at the end of a spanner 0.6 m long when the load on the bolt is 15 kN.

A square threaded bolt of mean diameter 24 mm and pitch 5 mm is tightened by screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of friction for the nut and bolt is 0.1 and for the nut and bearing surfaces 0.16, find the force required at the end of a spanner 0.6 m long when the load on the bolt is 15 kN.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.
3. A square threaded bolt of mean diameter 24 mm and pitch 5 mm is tightened by screwing a nut whose mean diameter of bearing surface is 50 mm. If the coefficient of friction for the nut and bolt is 0.1 and for the nut and bearing surfaces 0.16, find the force required at the end of a spanner 0.5 m long when the load on the bolt is 10 kN.
From the rotating shaft shown below, a force 100 N was pulled to reduce the shaft’s angular speed through its cables. What is the maximum cable tension if the shaft rotates in a counterclockwise direction? Use coefficient of friction on shaft equal to 0.2.
A triple-thread Acme-form power screw of 50 mm major diameter is used. The nut makes 1.5 turn per cm of axial travel. A force of 600 N is applied at the end of a 850 mm wrench used on the nut. The mean diameter of the collar is 90 mm. If the coefficient of friction at the thread and at the collar are 0.15 and 0.13, respectively. Determine the weight that is being lifted.
2 A ladder 5 m long and weighing 260 N is placed against a vertical wall at an inclination of 30 ^ 0 with wall. A wan weighing 780 N climbs the ladder. When he is at a distance of 1.64 m along the ladder from lower all contact surfaces? end, the ladder slips. What is the coefficient of friction assuming it to be same for
(6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head; the head is guided by linear slides with anti-friction bearings, and thus no appreciable friction is involved. If the coefficient of friction for the threads is 0.1, find: (a) the load that can be raised if the screw has 2 threads/in and an outside diameter of 2½in; (b) if a 4000-lb load is to be lowered, what torque must the screw transmit? (c) if the power screw of rotates 10 rpm, what is the linear speed of the driven head in feet per minute?
A steel tire, 20 mm thick, 90 mm wide, and 1600.0 mm inside diameter is heated and shrunk onto a steel wheel 1600.5 mm in diameter. If the coefficient of static friction is 0.40, what torque is required to twist the tire relative to the wheel? Neglect the deformation of the wheel. Use E = 100 GPa.
Steel frame with thickness of 10mm, width 80mm and inner diameter of 1500.0mm being heated and shrinkable on steel wheel diameter 1500.5mm. If the coefficient of static friction is 0.30, what is the torque required to roll the tire with respect to the wheel? Neglecting the deformation of the wheel. Use E = 200 GPa.
(2) A single square thread jackscrew has 2.0TPI. It is to lift 15 tons. The friction radius of the collar is 1-in. The coefficient of friction between the threads and screws and base is 0.15, that between the screw and collar is 0.13. Determine: (a) the diameter of the root of the screw if the allowable stress in compression is 6,000psi; (b) the pull required at the end of 5.0ft bar to raise the load; (c) the twisting moment exerted at the root of the threads; (d) the efficiency of the screw and collar.
Problem #10: A horizontal bar, 11 ft long and of negligible weight, rests on rough inclined planes as shown. The coefficient of friction for all contact surfaces is 0.27. What is the normal force at contact point A? How close to A may the 120 lb force be applied before motion impends?
A homogeneous ladder 20m long weighing 50 N is leaning against a wall makes an angle of 15 degrees with the wall. Assuming that the coefficient of friction at all contact surfaces is 0.20. What horizontal force (F) acting on the lower third point of the ladder will cause it to slip outward?