A steel bar of 50mm x 50mm in section and 150 mm length is subjected to tensile load of 300 kN along the longitudinal axis and tensile load of 500 kN and compressive load of 400 kN on the lateral faces. Determine the change in dimension of bar and the change in volume. Adopt E, = 2 × 10°N/mm? and u= 0.3.

A steel bar of 50mm x 50mm in section and 150 mm length is subjected to tensile load of 300 kN along the longitudinal axis and tensile load of 500 kN and compressive load of 400 kN on the lateral faces. Determine the change in dimension of bar and the change in volume. Adopt E, = 2 × 10°N/mm? and u= 0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Correct answer is 0.01163. Please show your solution. Determine the slope at the left support A (in degrees.). The beam is loaded with a moment load M = 19 kN-m at its midspan. EI is constant and equal to 35,111 kN-m^2. Use length of beam L = 9 m.
Determine the horizontal component of the force applied by the smooth circular guide on the mass A. mA = 2 kg, y= 100 mm, Vy = 0.6 m/s, ay = -0.2 m/s^2
In the figure, determine the value of S such that the resultant is 100 N downward and acting at 3 meter from the support.
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Determine the internal force and the change in length of section (1) of axial member CDE. Tension and elongation are positive. Compression is negative.Answer:F1 = kNδ1 = mm
Determine the horizontal displacement of joint C. Each A-36 steel member has a cross-sectional area of 400 mm2.
A simply supported beam, 9m long is subjected to a uniform load 20KN/m applied to the middle third of the beam. Determine the Maximum deflection, deflection at x=3, deflection at x=7.5. Determine the slope of B with respect to A. Determine the slope with respect to B. Determine the tangential slope of B with respect to A. Determine the tangential slope of A with respect to B.
Find deflection at midpont, max deflection, and slope under load p
The flexural rigidity, EI, is constant from point A to point D. Use point A as the origin for the x and y axes. Always use 3 decimal place in your final answer if it is not whole number. (Macaulay's Method)What is the slope at point A? in terms of 1/EIWhat is the deflection at point B? in terms of 1/EIWhat is the deflection at point C? in terms of 1/EIWhat is the reaction at the hinge support A? in kN (use 3 decimal places)What is the slope at point D? in terms of 1/EIWhat is the reaction at the roller support D? in kN (use 3 decimal places)
Determine the vertical displacement of joint C of the steel truss shown inFig.a. The cross-sectional area of each member is A = 400 mm2, and Est = 200 GPa.
Determine the displacement of point B of the steel beam as shown. Take E = 200 GPa, I = 500(106) mm4.
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
Double Integration The given overhanging beam is loaded as shown. Use E = 1.5 x 10^6 psi and I = 40 in^4. A) determine the deflection at point B in inches. B) determine the location of the maximum deflection from the left support in ft. C) determine the maximum deflection in inches and calculate the slope of elastic curve over the right support.