A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a 1-in.-diameter aluminum rod AC. Cables BE and DF, each of -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 75 ksi, and that the ultimate strength of the aluminum used for the rod is 43 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. 9 in. 9 in. 12 in. E 1 in. 4 ↑ B D 12 in. in. in. The largest load Q that can be applied is kips.

A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a 1-in.-diameter aluminum rod AC. Cables BE and DF, each of -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 75 ksi, and that the ultimate strength of the aluminum used for the rod is 43 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. 9 in. 9 in. 12 in. E 1 in. 4 ↑ B D 12 in. in. in. The largest load Q that can be applied is kips.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Similar questions

The column shown has a uniform rectangular cross-section. b = 14 mm and d = 24 mm. Assume both ends A and B are pinned supports.This Column ACB is laterally braced at its midpoint C suchthat rotation is allowed but translation is prevented alongthe y-axis direction.Use E = 200 GPa, and assume L = 600 mm.Knowing that a factor of safety of F.S. = 3.3 is required andusing Euler’s formula, determine the largest allowablecentric load Pall that can be applied to the column.
Question (1): A rectangular beam has a width b = 400 mm, and effective depth d = 850 mm and a total height h = 900 mm. The beam is subjected to an ultimate moment Mu = 1500 kN.m and an ultimate shear force Vu = 700 kN. 1- ) Design the beam for flexure to calculate the required area of steel. 2-) Using stirrups Φ 10 mm ( No.10) diameter, calculate the required spacing (s) between the stirrups at the ultimate shear force section. For all questions, Use f’c= 28 MPa and Fy= 420 MPa
Q#3. An aluminium strut 14 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER. THANKS
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
Design the spacing of the main bars and temperature bars of a one-way slabhaving a total span of 5 m. The slab is supported with hinge in the left support anda vertical cable located 1.5 m from the right support. The distance between thecables of the slab is 2.3 m. The slab is to carry a live load pressure of 2.4 kPa anda dead load pressure (including self-weight) of 4 kPa. Assume f’c = 27.6 MPa andfy = 276 MPa for main and temperature bars. Use 12 mm ∅ for main bars and 10mm ∅ for temperature bars. The slab is not exposed to earth or weather. Usethickness of slab of 120 mm. Use NSCP 2001.
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 3. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. 4. Determine the location of the maximum moment on the beam in meters.
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 7. Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, In MPa, on the fiber 30mm above NA at distance 1m from A
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb=260MPa on double shear. 1. Determine the location of centroid, y, from top of the beam in mm .
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear Determine the location of centroid, y, from top of the beam in mm Determine the moment of inertia, I, of the section in mm^4. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam Determine the maximum flexural stress on the beam in MPa.
Note: -The center of gravity (SG) is located at 477mm. Determine the factor of safety at points A and B located on the outer surface at the base of the pipe. use mohr's circleFactor of safety with maximum shear theory.Experts help with correct and all answers , dont waste qsn by wrong attempt.
A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 8-20-mm-diameter (28) longhitudinal bars equally distributed to the shorte sides of the column. Use f'c = 21 MPa and fy = 415 MPa. Calculate the required spacing of 10-mm-diameter ties, s (mm). Calculate the nominal axial strength of the column, Pn (kN). Calculate the maximum ultimate axial load the column can carry, Pu (kN)