Please do part 2 and 3 thank you A structural member is subjected to the plane stress condition,The state of stress at a point of the member is shown in the figure.16 MP(1) Draw the Mohr's circle for this 2D state of stress.2) Determine the principal stresses, the maximum inplane shoarstresses and associated normal stresses acting at this point.0) Represent these critical stresses on new stress elements, andindicate the angles of rotation of the new stress elements withrespect to the original stress elements.9 MP12 MP

For Mohr circleRadius, R=(σx-σy2)2+ζxy2 R=(-12-162)2+92 R=16.64 KN/m2Center,…

A structural member is subjected to the plane stress condition. The state of strem at a point of the member is shown in the figure. 16 MP (1) Draw the Mohr's circle for this 2D state of stres. a) Determine the principal stressen, the maximum in plane shear strosses and associated normal stresses acting at this point 0) Reprosent these critical stresses on new stres elements, and indicate the angles of rotation of the new stress elements with espect to the original stress elements MP 12 MP

A structural member is subjected to the plane stress condition. The state of strem at a point of the member is shown in the figure. 16 MP (1) Draw the Mohr's circle for this 2D state of stres. a) Determine the principal stressen, the maximum in plane shear strosses and associated normal stresses acting at this point 0) Reprosent these critical stresses on new stres elements, and indicate the angles of rotation of the new stress elements with espect to the original stress elements MP 12 MP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit N) act on the side faces of the cube whose dimension a = 20 mm. The limit stress for the uniaxial stress case in the material is 40 / Mpa safety coefficient n = 2. How many Newtons (N) is the largest P value according to the Von Mises assumption for the cube to be safe? please please fast help me
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 53°.
An element in uniaxial stress is subjected totensile stresses σx = 57 MPa, as shown in the figure.Using Mohr’s circle, determine the following.(a) The stresses acting on an element oriented at anangle θ =-33° from the x axis (minus meansclockwise).(b) The maximum shear stresses and associatednormal stresses.Show all results on sketches of properly orientedelements.
Plane AB is under pressure and Plane AB has an angle = 30 degrees to sigma = 50 nPa.a. Determine the equations used to calculate the normal and shear stress in the plane ABb. Draw a normal vector sketch on the plane AB and the angle formed between the normal vector andc. Calculate normal stress and shear stress in plane AB (Round up to 4 digits after comma)d. Plot the point normal stress and shear stress plane AB on the Mohr Diagram sketch.
Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements (10 marks)
Mechanics of Materials (Statically Indeterminate Members) A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown in the figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stress developed in segments AB and BC.
An element in uniaxial stress is subjected to a tensile stress of 49mpa in x-direction. Determine the stress acting on element oriented at an angle of -27degree celcius from x-axis(clockwise direction)
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 ksi, Sy = 24 ksi, and Sxy = 16 ksi. (a) Determine the principal stresses (0p1 > 0p2) and the maximum in-plane shear stress max acting at the point. (b) Find the smallest rotation angle Op (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
Question 1: The general state of stress at a point is characterized by six independent normal and shear stress components which act on the faces of an element of material located at the point. Show a schematic view of the general state of stress. Using Mohr’s circle, determine the principal stresses of an element having σx = 45 MPa, σy = 55 MPa and ?xy = 25 MPa. Show them on a sketch of a properly oriented element. Using Mohr’s circle, determine the maximum and minimum shear stresses. Show them on a sketch of a properly oriented element. Determine the equivalent state of stress if the element is oriented 30º clockwise by using Mohr’s circle. Show them on a sketch of a properly oriented element.
Figure shows a state of plane stress consists of normal stresses σx = 60 MPa and σy = -40MPa; and unknown shear stress, ?xy. The maximum principal stress was determined to be 104.34 MPa. Using Mohr’s circle, determine; the magnitude of the shear stress, the principal plane and the minimum principal stress. Then, sketch the element showing all stresses in its proper orientation, the maximum shear stress, associated normal stress and the orientation of the element. Then, sketch the element showing all stresses in its proper orientation, the stress components acting on the inclined plane AB. Then, sketch the element showing all stresses in its proper orientation.