A substance has a melting point of 20°C and a heat of fusion of 2.4 × 10 to power of ((4)) J/kg. The boiling point is 150°C and the heat of vaporization is 4.8 × 10 to power of ((4)) J/kg at a pressure of 1.0 atm. The specific heats for the solid, liquid, and gaseous phases are 600 J/(kg • K), 1000 J/(kg • K), and 400 J/(kg • K), respectively. The quantity of heat required to raise the temperature of 3.00 kg of the substance from 9°C to 98°C, at a pressure of 1.0 atm, is closest to

A substance has a melting point of 20°C and a heat of fusion of 2.4 × 10 to power of ((4)) J/kg. The boiling point is 150°C and the heat of vaporization is 4.8 × 10 to power of ((4)) J/kg at a pressure of 1.0 atm. The specific heats for the solid, liquid, and gaseous phases are 600 J/(kg • K), 1000 J/(kg • K), and 400 J/(kg • K), respectively. The quantity of heat required to raise the temperature of 3.00 kg of the substance from 9°C to 98°C, at a pressure of 1.0 atm, is closest to

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.28P

See similar textbooks

Similar questions

Define the following terms: a. heat of fusion b. heat of vaporization c. heat capacity d. boiling point of water e. freezing point of water
a) What is latent heat of vaporization? Latent heat of fusion? b) Assuming a solid material has a specific latent heat of fusion of 334 kJ/kg, what is the energy required to completely melt this material? Mass = 20 kg? c) If the material from part b melts at 200oC and starts at 20oC, what is the total amount of energy required to both bring it to its melting point and melt all of the material? (Cp = 18 kJ/kgK)
Plasma pressures of 10^4 bar may be routinely created during an isentropic compression. What is the minimum confinement time (in ms) that would be necessary for fusion reactions to occur during isentropic compression?
8. The combustion of 1.00 mole of glucose, C6H12O6, liberates 1.90 x 103 kJ of heat. If 2.30 g of glucose is burned in a calorimeter containing 0.560 kg of water, and the temperature of the assembly increases from 22.5 C to 26.7 C, what is the heat capacity of the calorimeter?
Calculate w and ΔE when 1 mole of a liquid is vaporized at its boiling point (80.°C) and 1.00 atm pressure. ΔH for the vaporization of the liquid is 30.7 kJ/mol at 80.°C. Assume the volume of 1 mole of liquid is negligible as compared to the volume of 1 mole of gas at 80.°C and 1.00 atm.
a) At an engine speed of 1000 rpm, what is the approximate penetration depth of the temperature fluctuations in (a) a cast iron block and (b) an aluminum engine block? b) Measurements of the exhaust gases of a hydrogen-fueled engine indicate a composition of 71.0% N2, 25.0% O2, and 3.9% H2O. At what equivalence ratio was the engine operated?
Calculate the power rating (in kW) of completely combusting 36 kilograms of n-butane if the entire combustion process takes 13 minutes. Assume that there are no excess reactants, the reactants are at 25oC and 1 atm and the products are returned to the same conditions at the end. Report your answer without decimal points.
Identify all the processes involved in a phase change involving absorption of heat and describe each.
The energy densities of various types of coal are listed below: Anthracite 35kJ/g Subbituminous 31kJ/gBituminous 28kJ/g Lignite 26kJ/gAn unknown sample of one of these coals is burned in an apparatus with a calorimeter constant of 1.3kJ/°C. When a 0.367-g sample is used, the temperature change is 8.75°C. Which type of coal is the sample?
Which best explains why the trend in noble gas boiling points increases down the group (larger in size)? A. Increasing dipole-dipole interactions B. Increasing dispersion interactions C. Increasing ion-ion interactions D. Increasing hydrogen bonding interactions
One mole of Carbon Dioxide burns completely in the presence of 3 moles of diatomic oxygen in a constant volume enclosure. The original temperature and pressure of the reactants are 25 C and 1 atm. A) If combustion takes place adiabatically calculate final temeprature and pressure of the products. B) If combustion does not take place adiabatically calculate the heat transfer per mole of CO when the products are cooled to a final temperature of 500K.
Shown to the right is the solid-liquid phase behavior for mixtures of component A and component B at 1 atm. Use the phase diagram to answer the following questions. a) Specify the melting point of substance B at 1 atm b) What is the maximum composition (mole fraction) of component B that is possible for the mixture to exist in phase S2? At what temperature does this occur? c) 20mol of component A and 180mol of component B are mixed at 350°C and 1 atm. The mixture is cooled at constant pressure to 200°C. i) What phases are present at the final state? ii) What is the composition of each phase at the final state? iii) What is the number of moles of each phase at the final state?