A synchronous motor with delta conductive coils is fed from a 480V source. Its synchronous impedance is 12, the product winding resistance is neglected, and the ferrous losses and friction losses are neglected as well. Find the following: A) If it is running a 400hp load at a power factor of 0.85 lead, find the value and angle of E and I B) If the field current increases by 10%, explain the motor behavior using the vector diagram. (C) Find the values of Eph, Iph, and IL after increasing the load

A synchronous motor with delta conductive coils is fed from a 480V source. Its synchronous impedance is 12, the product winding resistance is neglected, and the ferrous losses and friction losses are neglected as well. Find the following: A) If it is running a 400hp load at a power factor of 0.85 lead, find the value and angle of E and I B) If the field current increases by 10%, explain the motor behavior using the vector diagram. (C) Find the values of Eph, Iph, and IL after increasing the load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase induction motor is rated at 5 hp, 1760 rpm, with a line-to-line voltage of 220 V rms. The motor has a power factor of 80 percent lagging and an efficiency of 75 percent under full-load conditions. Find the electrical input power absorbed by the motor under full-load conditions. Also, find the rms line current.
a 3-phase, 220-v, 50-hz, 1500 r.p.m., mesh-connected synchronous motor has a synchronous impedance of 4 ohm per phase. it receives an input line current of 30a at a leading power factor of 0.8. find the line value of the induced e.m.f. and the load angle expressed in mechanical degrees. if the mechanical load is thrown off without change of excitation, determine the magnitude of the current under the new conditions. neglect losses.
A 2-pole, single-phase alternator driven at 3000rpm require a mechanical input to its rotor of 30kW when it is delivering its full-load output of 30kW. Under this condition the fixed and variable losses are1100W and 2.8kW respectively, and the rotor field winding is supplied from a 110V dc source. Given that the full-load efficiency is 87%, determine. the frequency generated, the input driving torque on full-load and the rotor field current
3) The conversion ratio of an asynchronous motor with 415 V, 3-phase, 60Hz, 6-pole, Y-connected rotor winding is a = N1 / N2 = 1.5,Parameter values per phase transferred to the stator are given below. a) For the case where slip s = 0.05, calculate the stator current, the torque generated in the motor, with the rotor circuit voltageCalculate the frequency.b) Subtract the Thevenin equivalent.c) The rotor stays stuck while the motor is running under load. Find the rotor current reflected to the stator at this instant.d) Find the maximum torque the motor can produce.e) It is required that the engine initially develops with maximum torque. For this, externalFind the value of the resistance transferred to the stator
A 25-hp three-phase induction motor operates for a 440-Vrms (line-to-line) three phase source and draws a line current of 35 A rms at a power factor of 83 percent lagging under rated full load conditions. The full load speed is 1750 rpm. Under no load conditions the speed is 1797 rpm and the line current is 6.5 A rms at a power factor of 30 percent lagging. Find the power loss and efficiency with full load, the input power with no load and the speed regulation.
A 3-phase induction motor having a synchronous speed of 1200 rpm draws 70kW from a 3-phase feeder.The copper losses and iron losses in the stator amount to 4kW.Friction and windage losses amount to 2kW.If the motor runs at 1170 rpm, determine the a. active power transmitted to the rotorb. rotor copper lossesc. mechanical power developedd. the mechanical power delivered to the loade. efficiency of the motor.
An 410-V, 3-phase, wye-connected, round-rotor synchronous motor operates at unity power factorwhile developing a power of 62 kW. If the synchronous reactance is 1.0 Ω per phase and thearmature resistance is negligible, calculate (i) the induced voltage per phase and (ii) the powerangle.
An industrial plant has a load of 800 kW at a power factor of 0.8 lagging. It is desired to purchase a synchronous motor of sufficient capacity to deliver a load of 200 kW and also serve to correct the over-all plant power factor to 0.92. Assuming that the synchronous motor has an efficiency of 91 percent, determine its kilovolt-ampere input rating and the power factor at which it will operate. write necessary details
A 460 V, 50 kW, 50 Hz, three-phase synchronous motor has a synchronous reactance ofXs = 4.15 Ω and an armature-to-field mutual inductance of Laf = 83 mH. The motor isoperated with rated terminal voltage and an input power of 40 kW. Calculate themagnitude and phase angle of the generated phase back-emf, E af , and the correspondingfield current, If , if the motor is operating at (a) 0.85 power factor lagging
At standstill condition, the outer impedance of the outer cage of the double cage induction motor=(0.3+j0.40)ohm and the inner cage is (0.1+j1.5)ohm. Neglect the stator impedance. Find the ratio of the output to input current and the ratio of the output torqu to the inout torque.
A 440-V-rms (line-to-line voltage) three-phase induction motor runs at 1150 rpm driving a load requiring 15 Nm of torque. The line current is 3.4 A rms at a power factor of 80 percent lagging. Find the output power, the power loss, and the efficiency.
Find the steady-state torque–speed relation for a compound-wound motor. The following parameters are given: Rf1=Rf2=10Ω, Ra= 2 5Ω, Rf=20Ω, and k= 1 N.m/A . Assume that the supply voltage is 115 V. Plot the steady-state torque–speed curve.( need only handwritten solution .otherwise downvote.)