25A telephone cable is clamped at A to the pole AB. Knowing that thetension in the right-hand portion of the cable is T2 = 1000 lb, determineby trigonometry (a) the required tension T, in the left-hand portion ifthe resultant R of the forces exerted by the cable at A is to be vertical,(b) the coresponding magnitude of R.TB.

Answered: Image /qna-images/answer/42386fba-bb35-48ff-a640-243942512c8c.jpg

A telephone cable is clamped at A to the pole AB. Knowing that th tension in the right-hand portion of the cable is T2 1000 lb, determin by trigonometry (a) the required tension T, in the left-hand portion the resultant R of the forces exerted by the cable at A is to be vertica (b) the corresponding magnitude of R.

A telephone cable is clamped at A to the pole AB. Knowing that th tension in the right-hand portion of the cable is T2 1000 lb, determin by trigonometry (a) the required tension T, in the left-hand portion the resultant R of the forces exerted by the cable at A is to be vertica (b) the corresponding magnitude of R.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cable is attached to the 20 kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
The rectangular beam ABC, 133 mm wide by 322 mm deep, is supported by a pin at A and the cable CD. Determine the normal stress (in MPa) at the bottom of the beam and at asectionofthebeam 1.07 m from the pin if P = 499.99 kN.
The rigid bar AB is supported by a cable BC and a pin at A. The diameter of the cable is 16 mm and themodulus of elasticity is 200 GPa. Calculate the vertical movement of the point B knowing that P=15kN
Two separate cables AC and BC support asign structure of weight W = 1575 lb attached to abuilding. The sign is also supported by a pin supportat O and a lateral restraint in the z-direction at D.(a) Find the tension in each cable. Neglect the massof the cables.(b) Find the average stress in each cable if the areaof each cable is Ae = 0.471 in2.
Cables extend from A to B and from A to C. The cable AC exerts a 1000-lb force F at A. What is the angle between the cables AB and AC? Determine the vector component of F parallel to the cable AB.
Three loads are suspended as shown from the cable ABCDE. Knowing that dc = 3 m, determine the sag at DB
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
Three cables are connected at A, where the forces P and Q are applied as shown. Knowing that Q = 0, find the value of P for which the tension in cable AD is (321) N.
The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 204 N and if a = 3m, determine the magnitude of force P(N). Round off only on the final answer expressed in 3 decimal places.
2.4. Two cables are tied together at C and loaded as shown. Knowing that P= 360N,Determine the tension in cable BC and AC. 1 Free-body Diagram only
Determine the force P on the cable if the spring is compressed 0.5 in. when the mechanism is in the position shown. The spring has a stiffness of k = 800 lb/ft.
Determine force Q and cable force TDE