A tensile stress is applied along the longitudinal axis of a cylindrical brass rod that has a diameter of 10 mm. Determine the magnitude of the load required to produce a change in diameter of 2.5 x 103 mm if the deformation is entirely elastic. Values of elastic modulus and Poisson's ratio for brass are 97 GPa and 0.34 respectively.

A tensile stress is applied along the longitudinal axis of a cylindrical brass rod that has a diameter of 10 mm. Determine the magnitude of the load required to produce a change in diameter of 2.5 x 103 mm if the deformation is entirely elastic. Values of elastic modulus and Poisson's ratio for brass are 97 GPa and 0.34 respectively.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Similar questions

A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear elastic behavior.
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.45 cm & the external diameter of 24.7 mm is subjected to an elastic tensile load of 251 kN. Take the elastic modulus of the aluminum specimen as 71 GPa and the initial length of the hollow cylinder as 198 mm. Solution: Cross-sectional Area (in mm2) = Stress-induced (in N/mm2) = Strain-induced (at least 3 decimal places accuracy)= Elongation (in mm) =
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17 kips. Determine the ratio of the shear modulus to the modulus of elasticity of a material whose Poisson's ratio is 0.25.
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.1 cm & the external diameter of 22.7 mm is subjected to an elastic tensile load of 271 kN. Take the elastic modulus of the aluminum specimen as 73 GPa and the initial length of the hollow cylinder as 186 mm. Solution: i) Cross-sectional Area (in mm2) = ii) Stress-induced (in N/mm2) = iii) Strain-induced (at least 3 decimal places accuracy)= iv) Elongation (in mm) =
Acetal plastic has a stress-strain diagram as shown. If a bar of this material has a length of 3 ft and cross-sectional area of 0.875 in2, and is subjected to an axial load of 2.5 kip, determine its elongation.
A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is heated and shrunk to a steel wheel 800.5 mm in diameter. The modulus of elasticity E = 200 MPa. a. Determine the tensile stress in the tire. b. Determine the compressive pressure between the tire and the wheel. c. Determine the thickness of the tire to resist a pressure of 1.5 MPa if it has an allowable stress of 124 MPa. I need answer ASAP. Thank you!
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.
2. A bar of thickness 15mm and having a rectangular cross-section carries a load of 120kN. Determine the minimum width of the bar to limit the stress to 200MPa. The bar, which is 1m long, extends by 2.5mm when carrying a load of 120kN. Determine the modulus of elasticity of the material of the bar.
A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of the hoop formed by the band is 29.98cm . By how much will it be necessary to increase the temperature of the hoop, so that it would slide over the surface of the cylinder ? What stress will occur in the hoop when it reaches the same temperature as the cylinder , if the deformation of the cylinder may be neglected ? (Write complete solution)