A thermodynamic steady flow system receives 4.56 kg per minute of a fluid work pressure is equal to 1307.90 kilo pascal and specific volume is equal to 0.0388 m3 per kg, speed equals 122 m per second specific internal energy is equal to 17.16 kj/kg. The fluid leaves the system in the boundary where pressure is equal to 551.6 kpa. specific volume is equal to 0.193 cubic meter per kg speed equals 183 m per second and specific internal energy 52.8 kj/kg. Dream passage through the system the fluid receives 3,000 J/s of heat. determine the work in kilojoule per minute.

A thermodynamic steady flow system receives 4.56 kg per minute of a fluid work pressure is equal to 1307.90 kilo pascal and specific volume is equal to 0.0388 m3 per kg, speed equals 122 m per second specific internal energy is equal to 17.16 kj/kg. The fluid leaves the system in the boundary where pressure is equal to 551.6 kpa. specific volume is equal to 0.193 cubic meter per kg speed equals 183 m per second and specific internal energy 52.8 kj/kg. Dream passage through the system the fluid receives 3,000 J/s of heat. determine the work in kilojoule per minute.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.49P

See similar textbooks

Similar questions

To determine the thermal conductivity of a structural material, a large 15-cm-thick slab of the material is subjected to a uniform heat flux of 2500 W/m2 while thermocouples embedded in the wall at 2.5 cm. intervals are read over a period of time. After the system had reached equilibrium, an operator recorded the thermocouple readings shown below for two different environmental conditions: Distance from the Surface (cm) Temperature (C) Test 1 0 40 5 65 10 97 15 132 Test 2 0 95 5 130 10 168 15 208 From these data, determine an approximate expression for the thermal conductivity as a function of temperature between 40 and 208C.
The Helmholtz free energy of a liquid column that rises, due to surface tension, inside a capillary tube (Figure 1), as a function of the height, h, is given by: F(h) =(ro)gr^2h^2/2 = -2 pi sigma r h cos teta, where r is the radius of the tube, g is the local ac- celaration of gravity, is the surface tension of the liquid, and is the contact angle of the liquid in contact with the wall of the tube. (a) From this expression, obtain the value of h as a function of the other physical parameters at equilibrium.Calculate the height that water will rise in a capil-lary of diameter 0.05mm. Assume that the contactangle between the water and the tube is zero. Thesurface tension of water at experimental conditionsisσ= 7.73×10−2N/m, and the local accelarationof gravity isg= 9.7m/s2.
40. Water flows through a pipe of varying cross-section and varying elevation at the rate of 22.2m3/min. At one section of the pipe 3 m from the ground, the radius of the pipe is 36 cm and the pressure is 12 N/cm^2.What is the pressure at a section where the radius of the pipe is 18cm and is 0.7 m from the ground level?A. 136 123 N/m2 B. 50 N/cm2 C. 750 000 N/m2 D. 12 N/cm2
A spaceship has crashed into an ocean on an unknown planet with radius 6.42 * 10 ^ 6 * m and mass 5.82 * 10 ^ 24 The atmospheric pressure at sea level is 202.0 kPa and the ocean has density of 0.817 * 10^ 3 kg/m3 . If the spacecraft can withstand external pressure of 3 atm how deep will the craft sink before being crushed?
10. A thermodynamic steady flow system receives 4.56 kg per min of a fluid where, P1=137.90 kPa, v1=0.0388 m^3/kg, ϑ1=122 m/s, and u1=17.16 kJ/kg. The fluid leaves the system at a boundary where P2=551.6 kPa, v2=0.193 m^3/kg, ϑ2=183 m/s, and u2=52.80 kJ/kg. During passage through the system the fluid receives 3000 J/s of heat. Determine the work in kJ/min.
1. The unit velocity head is a. ft-lbf/lbm b. ft-lb/sec c. ft-lbm/ft^3 d. ft-lbf/sec 2. Bernoulli’s equation describes a. kinetic energy balance in laminar flow b. mechanical energy balance in boundary layer c. mechanical energy balance in potential glow d. mechanical energy in turbulent flow 3. The continuity equation a. relates work and energy b. is only applicable to liquid c. relates masa flow rate along a stream tube d. stipulates that newtons second law of motion must be satisfied at every point in the fluid
In a horizontal tube, its initial section is A1 = 800 cm2 , which reduces to A2 = 600 cm2 at the end of the tube. The mass amount is 0.1 slug/s of air (p = 1.25 kg/s). Assuming ideal fluid flow and steady state, calculate the pressure difference between A1 and A2. Answer:p1 - p2 = 1.75 kgf/m2
A steel ball with a diameter of 10 mm is taken suddenly from a medium at a temperature of 25ºc and annealed for 20 minutes in the furnace host at a temperature of 800ºc. How many ° C is the temperature of the steel ball when it comes out of the oven? (ρ(steel) = 7854 kg / m3, C(steel) = 434 J / kgK, h(air) = 10 W / m2K and h(oil) =100 W / m2K) a. 705.65 b. 662.90 c. 706.25 d. 750.81 e. 750.20
THERMODYNAMICS Question 0.5 kg/s of an idea gas (molecular weight 30, ratio of specific heats 1.5) is cooled at constant pressure from 500 K to 400 K, without any mechanism for absorbing or producing work. At what rate is heat removed from this gas flow in kW?
In the United States, energy for household heating is generally sold using English units, e.g., therm, gal, and cord. A house in Wisconsin uses 1200 therms of thermal energy during the heating season. Calculate the cost of fuel if the furnace uses (a) natural gas with an efficiency of 70%; (b) No. 2 fuel oil, efficiency 65%; (c) kerosene, efficiency 99.9% (unvented); and (d) wood with l5% moisture with an efficiency of 50%. Use the data in Tables 2.2, 2.7, and 2.13. The efficiencies are based on the HHV. Assume the cost of natural gas is $8/MBtu, the cost of No. 2 fuel oil is $3/gal, the cost of kerosene is $3.50/gal, and the cost of wood is $100/cord. Assume the bulk density of cord wood is 30 lbm/ft3 .
Air at atmospheric pressure enters a heating duct with dimensions of 3 x 6 in. The air enters the 16 ft long duct with a temperature of 32 F, and the duct surface is maintained at 150 F. If the air exit temperature is to be 68 F, what is the air flow, in lb/hr? (answer in whole number) For air, R = 53.342 ft-lbf/lbm-R, k = 0.173 Btu-in/ft2-hr-F, and cp = 0.24 Btu/lbm-
the title of the book: Engineering Thermofluids Thermodynamics, Fluid Mechanics, and Heat Transfer by: Mahmoud Massoud