a thermometer is taken from a room in which the temperature is 75ºC into the open, where the temperature is 35ºC, and the thermometer reading is 65ºC after 30 sec, what will be the thermometer reading 3 minutes after the removal? Use 2. decimal places.

a thermometer is taken from a room in which the temperature is 75ºC into the open, where the temperature is 35ºC, and the thermometer reading is 65ºC after 30 sec, what will be the thermometer reading 3 minutes after the removal? Use 2. decimal places.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 3P: Alcohol thermometers can measure temperatures in the range of 100 F to 200 F Determine the...

See similar textbooks

Related questions

Q: power P required to drive a fan or blower depends upon iscosity μ, impeller diameter D, flow rate Q…

A: solution of above problem is below:

Q: 2.16 A large cement kiln has a length of 400 ft and a diameter of 20 ft. Determine the change in…

Q: 3. The number of zero-force members of the following truss is eight. 201

Q: 2.2. A pump adds 40 m against a closed delivery pump, 37 m at discharge of 170 L/s and 25 m at…

A: Given, H1 = 40 m H2 = 37 m H3 = 25 m

Q: 10 kN 21 20 KN 1=3 m d 7=3m 1-3 m Which of the following most nearly gives the vertical displacement…

Q: and (b) the maximum deflection. Draw also the e. Assume El constant. E = 200 GPa, I =

Q: A cylindrical tank with closed ends contains compressed air at 850 kPa. The inside diameter of the…

A: Given :

Q: Depth of wall ype of support Dewatering/Piping

A: Generally 4 types of wall is used in excavation for stability of excavation work.…

Q: Write equations for the shearing force and bending moment at any point in the beam and plot shear…

Q: Find the corresp g/m³.Density of ity of water 0.C =

Q: * Q2: The ladder in fig.(1), has a uniform weight of 100N and rests against the wall at B.If the…

Q: A fan is used to force air having a temperature of 20°C theough the 200 mm diameter galvanized sheet…

Q: 20 kN A 30 kN/m F B 16 kN =10 C 2m 4m 4m 3m Which of the following most nearly gives the maximum…

Q: Which description is correct about the elevation? (multiple choice) A The elevation datum is the…

A: This is a multiple choice questions here all given questions are from surveying engineering

Q: Apply the terminology to a construction technology to a given building construction project.

A: Given data:- Concrete:-Concrete is a mixture of cement, water, and aggregates & In concrete…

Q: errors that might happen on this lab test and how to prevent it?

A: Density, Absorption and Voids in Hardened Concrete lab test The density test in hardened concrete is…

Q: what is concrete formwork and shoring? (pls give me a detailed research about it)

Q: Evaluate how the functional characteristics and design selection criteria impact on the eventual…

A: Construction has several elements, and conceptual design is among the most significant in creating…

Q: Discuss at least 5 different types of Logistic infrastructures Compare between India with Canada…

A: Logistic Infrastructures in India include : Transportation of Goods (Multimodal) Carriage of goods…

Q: Compute the value of EIS at point B of the simply supported beam ABC using moment area method. 600…

A: Find EIδ Value at B using moment area method

Q: for the beam shown in figure, find the deflect. end by using double integration method? use

Q: (c) Liquid flows through an orifice in the bottom of a cylindrical tank at a velocity of 4m/s. If…

Q: The absolute specific gravity of a soil sample with the saturated unit weight and dry unit weight as…

A: True/Absolute specific gravity Absolute specific gravity, if applicable When measuring the actual…

Q: B find the max Value of (P) that can be applied on the Cantilever beam Shown in figure, knowing that…

A: Consider the given beam. Calculate the moment in the beam as follows. M=Pcosθ×450=P×35×450=270P N·mm

Q: 1m 2.5 kN/m Rislo 5 kN þ 3m

A: , ',c, ,

Q: A static center-point bending test was performed on a 50 X50 X760 mm wood sample according to ASTM…

A: Given data:- Length of span, L=710 mm Maximum load, w=2.67 kN Width of beam, b=50 mm Depth of beam,…

Q: A massless beam has a loading pattern as shown in the figure. The beam is of rectangular cross…

A: Given data in question UDL Span member length = 4000 mm Cross section To find out Bending stress

Q: Agitate the sieves by hand or by mechanical apparatus for a sufficient period. The criterion for…

A: Increasing the agitation duration increases the likelihood of a particle and an open sieve aperture…

Q: Wood has a distinct structure that affects its use as a construction material. Civil and…

A: Definition •Wood reasonable for building or other designing purposes is called timber-Standing…

Q: Cantilever beam loaded as shown in fig., draw the shear force diagram and bending moment diagram. 20…

Q: determine the largest allowable spacing of rivets that join (a) the angle bars and the top plate;…

A: The Working stress of shear and bearing is given as 100 and 250 MPA yu

Q: What is the laminar entrance length in a 4-cm diameter pipe if 2 x 105 m³/s of water is flowing at…

Q: al pressure ection is kno

A: solution of above problem is below:

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

A: Given: The resultant force is 590 lb about the y-axis. The value of F1 is 370 lb. The value of F2 is…

Q: he jib crane is designed for a maximum capacity of 4 kN, and its uniform I-beam has a mass of 210…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Flow over lengthy pipelines is seen in oil processing. A pipeline with a 4-inch schedule 40 steel…

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

Q: One of the columns supporting the roof of a large building exerts a load of 1500kN on a circular…

A: The design of the footing is based on the criteria, qn ≤ qna where qn - Net pressure from the…

Q: Using AREA METHOD, draw the shear and moment diagrams of the beam loaded as shown. (Thank you) 6…

Q: A cylinder is made of steel plate is intended to be used as a container for compressed air. The…

Q: Q.14. The velocity of flow in a badly corroded 7.5 cm pipe is found to increase 20% as a Pinot tube…

A: Let assume the flow as turbulent ; uu' = 2.5 loge yε + 8.5 where ; u = Velocity at y u ' =…

Q: M(N) Problem 8. Draw the load and shear diagram from the given moment diagram. 3.600 2m 5.625 3m…

Q: Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal…

Q: Problem 2.1 The Grashof number, Gr is defined as: (where g is gravitational acceleration, B is…

A: Grashof number is used to differentiate the flow type as below

Q: Oil (SG=0.8) discharges from a 250mm diameter pipe through a sharp-crested orifice whose dia is…

Q: The line of sight of a total station is out of adjustment by 10″.In prolonging a line by plunging…

A: Given:- out of adjustment by 10" To find:- angular error

Q: 1. A pump must be selected to deliver water to a tank that is 9m above a sump. The system to which…

A: Given, L = 100 m D = 100 mm or 0.1 m f = 0.006

Q: It is desired to remove dust particles (50µm) in diameter from (3.8 m³/sec) of air, using a…

Q: The post shown in the figure below (Figure 1) is made from GOGI-T6 aluminum and has a diameter of 50…

A: From figure ; FA + FB = P FB = P - FA --- 1 Fixed ends ; δAB + δBC = 0 ---- 2 Note that ; AC =…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Find the equivalent force couple system at the section a-a. Then using stress equation the normal…

Concept explainers

Hydrogen Energy

Energy is a quantity that cannot be defined, its existence can only be felt. In simple language, if a system possesses energy, it can do a specific kind of work. There are many forms of energy sources which people can use to obtain work. Solar energy, tidal energy, hydroelectric energy, geothermal energy, wind energy are some of the renewable energy sources which are primarily used for the production of electricity.

Question

If a thermometer is taken from a room in which the temperature is 75ºC into the open, where the temperature is 35ºC, and the thermometer reading is 65ºC after 30 sec, what will be the thermometer reading 3 minutes after the removal? Use 2. decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two thermometer. one reading and the other are both immersed in a fluid. If the farenheit reading is half of the celcius reading, a.) What is the farenheit reading? b.)what is the equivalent temperature of the fluid in degrees rankine?
A thermometer reading 75 degrees F is take out where the temperature is 20 degrees F. 4 minutes later, the thermometer reading is 30 degrees F. Find the time (in minutes) taken for the reading to drop from 75 degrees F to within half degree of air temperature.
calculate the pressure to be read in the (1) manometer in the visible appendix system. The relative distinctive mass of the oil is 0.75 and the relative distinctive mass of the mercury is 13.6.
1. A mercury barometer at the base of a mountain reads 28.95 in. At the same time, another barometer at the top of the mountains reads 23.22 in. Assuming w for air to be constant at 0.0765 lb per cu.ft, what is the approximate height of the mountain?
The initial reading differential manometer shown is exposed to the atmosphere at end B. a) Calculate for the pressure in pipe A and the pressure of the air inside the manometer. Express your answer in Pascals. b) Briefly explain why liquid manometers should be checked for air bubbles before being used. SG (pipe fluid)= 0.887 SG (manometer fluid) = 1.05 c = 22 cm d = 17 cm e = 25 cm
A thermometer reading 45℃ is brought outside where the temperature is 25℃. Five minutes later, the thermometer reading is 33℃. Determine the thermometer reading 10 minutes after the thermometer was brought outside. Your answer
Comment on the practicality of using hydrometer, pycnometer and viscometer to determine the specific gravity of the liquid, the density of the solid and the viscosity of different liquids, respectively.
NEWTON'S LAW OF COOLING A thermometer , reading 5° C , is brought into a room whose temperature is 22° C . One minute later the thermometer reading is 12°C . How long does it take until the reading is practically 20° C
The air temperature in a 26 in^3 container with a free sliding piston is initially measured at 45 degrees Fahrenheit. The temperature is raised to 180 degrees Fahrenheit. What is the new volume of the container? What are the absolute temperature readings initially and after the temperature has been raised? What is the volume in the cylinder after the temperature has been raised?
An anemometer measures the velocity of the air from a grill. The anemometerreading is 18 ft/m. What is the reading in meters per minute?
Solve the following application problems. The thermometer reading 70° F is placed in an oven preheated to a constant temperature. After ½ minute, the thermometer reads 110° F and it reads 145°F after 1 minute. What is the temperature in the oven?
A weather reports indicates the barometers pressure is 28.54 inches of mercury. What is the atmospheric pressure in pounds per inch?