A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glyceri (p = 1258 kg/m' and u = 1.49 Pa.s ) with a velocity of ( 7 m/s ). Compute th %3D skin frictional ( viscous ) drag exerted on the upper surface of the plate, if : a) The plate side parallel to the stream is the shortest side b) The plate side parallel to the stream is the longest side You may use the following relations: Cplam = 1.328 / Re, Cpturb = 0.072 / Re, %3D eerif

A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glyceri (p = 1258 kg/m' and u = 1.49 Pa.s ) with a velocity of ( 7 m/s ). Compute th %3D skin frictional ( viscous ) drag exerted on the upper surface of the plate, if : a) The plate side parallel to the stream is the shortest side b) The plate side parallel to the stream is the longest side You may use the following relations: Cplam = 1.328 / Re, Cpturb = 0.072 / Re, %3D eerif

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.26P

See similar textbooks

Similar questions

I need to know the characteristic uses of vertical axis wind turbines.
In one of the pilot plants, a 30 m diameter horizontal axis wind turbines (HAWT) are mounted with its hub at 50 m above a ground surface that is covered by shrubs and hedges. For the given pilot project, estimate the ratio of power in the wind per 1 m2 of rotor area at the highest point that a rotor blade tip reaches, to the lowest point that it falls to?
Name two basic applications for multiviews in architectural drafting.
A Savonius rotor can be approximatedby the two open half-tubes in Fig mounted ona central axis. If the drag of each tube is similar to thatin Table 7.2, derive an approximate formula for therotation rate Ω, as a function of U, D, L, and the fluidproperties (ρ, μ).
A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046 m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (2) Find the drag coefficient CD_________
Q/ ture or false -The flow curves are classified according to the number of reactors and the mechanism of separation or non-separation in the cores
A steam generator generates flue gas at an average temperature of 260 C inside a Chimney. The theoretical draft is 0.5 kPa and the ambient condition of the air is 21 C and 100 kPa. Assume the coefficient velocity to be 0.30 and the molecular weight of the flue gas is 32. For air-fuel ratio requirements per second of 15, calculate: a. The diameter of the Chimney, meter b. The theoretical draft, cm H₂O
(Aeronautical Engineering) Find the root chord, tip chord, and the mean aerodynamic chord of a straight tapered wing, given that the taper ratio is 0.65, the aspect ratio is 7.75, and the wing area is 520 square feet. Given:Req’d:Solution:
A group of students is designing a small, round (axisymmetric), low-speed wind tunnel for their senior design project. Their design calls for the axial component of velocity to increase linearly in the contraction section from uz, 0 to uz, L. The air speed through the test section is to be uz, L = 120 ft/s. The length of the contraction is L = 3.0 ft, and the entrance and exit diameters of the contraction are D0 = 5.0 ft and DL = 1.5 ft, respectively. The air is at standard temperature and pressure. (a) Verify that the flow can be approximated as incompressible. (b) Generate an expression for the radial velocity component ur between z = 0 and z = L, staying in variable form. You may ignore frictional effects (boundary layers) on the walls. (c) Generate an expression for the stream function ? as a function of r and z. (d) Plot some streamlines and design the shape of the contraction, assuming that frictional effects along the walls of the wind tunnel contraction are negligible.
Determine the velocity required for take off for an aircraft with the following characteristics.Aircraft mass: 7200 kgWingspan: 15 mWing shape: rectangularWing chord length: 1.8 mWing airfoil: NACA 4415Wing angle of attack: 7× 0.5 + 5 degreesHint: Check NACA charts for required parameters.
Suppose you are designing the propeller of a radio-controlled model airplane. The overall diameter of the propeller is 34.0 cm, and the hub assembly diameter is 5.5 cm. The propeller rotates at 1700 rpm, and the airfoil chosen for the propeller cross section achieves its maximum efficiency at an angle of attack of 14°. When the airplane flies at 30 mi/h (13.4 m/s), calculate the blade pitch angle from the root to the tip of the blade such that ? = 14° everywhere along the propeller blade.
Apply the necessary conversion factors to prove the relationship between dimensionless turbine specific speed and customary U.S. turbine specific speed, NSt = 43.46NSt, US. Note that we assume water as the fluid and standard earth gravity.