Answered: A three-phase motor is connected to a…

A three-phase motor is connected to a three-phase source with a line voltage of 440V. If the motor consumes a total of 55kW at 0.73 power factor lagging, what is the line current?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24MCQ: Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line...

See similar textbooks

Related questions

Q: S 25+3 XC+)

Q: Q4/ The decimal 793.251)= ( number number ( O 1431.204 O 1431.200 O No one of them O 1341.200 O…

Q: 1. Find the impulse response h [n] for each of the causal LTI discrete-time systems satisfying the…

Q: 30, The rotor of a 50 Hz, 4 pole synchronous motor is directly coupled to rotor of 50 Hz, 6 pole…

A: Given,The parameters of rotor of the synchronous motor,Frequency, f=50 Hz.Pole, P=4.and,The…

Q: For the following system, if the input X[k]= 8(k + 1) + 2.4k and output Y[k]= 2(k)u[k], the impulse…

Q: VI -2.000V V+ 20V R1-200k 3.000V R2=500k R3-1 Meg 1.000VW V3 +1V 3.791uV U1 V+ UA741 091 V- 20V RF-1…

A: To find the output voltage of the given summing amplifier

Q: Design a series resonant circuit with an input source voltage of 1020° V to have the following…

A: Given: Input source voltage, V=10∠0° Peak current, I=800mA Bandwidth, B.W.=120Hz Resonant frequency,…

Q: 1. What will the normal output level of a latch be if it is set? a. High b. Low 2. The complement…

Q: Calculate the power of the following signal

Q: The Z-transform of the following function f[k] = 2.2k +$.(-5)* - 3 (-4)* 33 is 42 so the constants A…

Q: Problem 2.4b: Sketch double sided and single sided amplitude and phase spectra of the following.…

Q: Q6/F1-A'B'+B'C+ABC+A'C' F2=A+B'C+A'C F3=B'+ABC F4=A'B+AB'C+A'BC' Chose the correct answer O F1-F3 O…

Q: 6. Please prove the following: X 8(kx) * () = S(x) k where is convolution operation, and k is a…

Q: design using JK-flip flops a logic circuit that detects the nonoverlapped sequence [10011]

Q: The average per of a load is 2.76 KW with a lagging power factor of 0.914. The magnitude of the rms…

Q: tan2t8 (t - 7/3 8

Q: Q5/Find the addition result for the following operation (66)8+ (1100)EX-3+(83)10- (F2.1)16 using 2's…

A: Given: (66)8+(1100)Ex-3+(83)10-(F2.1)16 To do: We have to perform the above addition using 2's…

Q: What are Hall probes and how they work?

A: A Hall probe is a tool that uses a calibrated Hall effect sensor to measure a magnetic field's…

Q: A (Β) 9 ΚΩΣ ον I 4 ΚΩ ww 3 ΚΩ 6ΚΩ • 12 ΚΩ 1,(6K + 4K) – 13(6K) = −6 –1(6K + 4K) + I,(6K) = 6 11(6K +…

Q: For the following system, if the input x[k]= 8(k+ 1) +2.4k and output Y[k]= 2(k)u[k], the in…

Q: 4 Pole's DC generator delivers a current of 100 A at 230 V. It has 1500 armature carriers attached…

Q: For the following system, if the input X[k]= 8(k+ 1) +2.4k and output Y[k]= 2(k)u[k], the impulse…

Q: Figure 1 shows the series circuit with the 60V supply. Calculate: i. The current /. ii. The voltage…

A: The given circuit is,

Q: There are 160 slots in a 3-phase, 8-pole, 50 Hz., star connected alternator. There are 4 conductors…

Q: Write the equation of unit step function for the figure below.

Q: At Node Vx, applying KCL gives:

Q: The span of the same leveled transmission line is 300 meters. The carrier's diameter is 15…

Q: Plot the indicated product g(t) of the functions below. X g(t) Multiplication

Q: 1.) Complete the truth table of a NOR gate D flip-flop shown below. R D T I 3 INPUTS OUTPUT S D T Q…

Q: Q7/Chose the correct answer for the output Q of the following circuit (Assume that A…

Q: Kindly give explanation An amplifier has a gain of 14 dB. Its input power is 8 mW. Find its output…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: In the circuit shown below, find the value of supply voltage V so that 20-ohm resistor can dissipate…

A: We have an circuit as shown in figure, We have been asked to find the, supply voltage if we want…

Q: The MOSFET has on-resistance

Q: SS 18-23 The input in Eigure P18-23 is i, (t) = 10e-5 mA. Use Fourier transforms to find i, (t).…

Q: Q4/ The decimal 793.251)= ( number number ( O 1431.204 O 1431.200 O No one of them O 1341.200 O…

Q: Sketch a waveform for a signal, x(t) = 5 sin 754 t with time in seconds.

Q: 1. Compute the transfer function () for the block diagram given below. R(S) R(S) G1 G2 H1 Substitute…

Q: Please answer this question with proper explanation

A: According to the question, it is given that Number of amplifiers = 6 Lower cut-off frequency fL =…

Q: A 70-Vac source has the following waveform. Determine: a. Vpk b. Vpk-pk c. Vrms d. Period e.…

A: NOTE : As per our company guidelines we are supposed to answer first three sub-parts only.…

Q: The positioning system of a printer can be modeled as Y(s) = where the input R (s) represents the…

A: Given: Positioning system is modeled as, Ys=10s+50s2+60s+500Rs. Input is unit step.

Q: 1;, = 2.75 mA Α- Figure 6-9 ΙΚΩ 1.5 Κ Ω | 4.7 ΚΩ Μ 3.9 Κ Ω Jour B Given the circuit in Figure 6-9,…

A: The given circuit is,

Q: 4. A three phase, 50 Hz induction motor has a full load speed of 1440 rpm. The full load slip will…

A: Given, A 3 phase induction motor has, Rated frequency, f=50 Hz. Full load rated speed, Nr=1440 rpm.…

Q: the figure below, where f 60kHz, 45kHz, 25kHz if ide

A: Given:

Q: Give five factors that affect electrical conductivity and why.

A: The movement of electrons is the foundation of electrical conductivity. Because they let electrons…

Q: Four dies of electric material having relative permittivities 4, 5, 6 and 7 and thicknesses of 2 mm,…

Q: • Create a new relay logic that will simplify the logic below. + A B C HH #HE D # C * A B #F (M) DC…

Q: 4. How long can a 12 Volt car battery supply 250 Amps to a starter motor if the battery has 4 * 106…

A: Given: Voltage of car battery, V=12 V. Current, I=250 A. Chemical energy in battery, E=4×106 J.

Q: Problem 13. The hot resistance of a 240 V filament lamp is 960 2. Find the current taken by the lamp…

A: Given, Resistance of filament, R=960 Ω. Voltage, V=240 V.

Q: Q5: A unity feedback system shown in Figure 5, operating with a damping ratio of 0.5, design a…

Q: 2V -5V

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

A three-phase motor is connected to a three-phase
source with a line voltage of 440V. If the motor
consumes a total of 55kW at 0.73 power factor
lagging, what is the line current?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the circuit shown below, the 3-phase induction motor is connected across a 3-phase, 440 V source. Assuming a phase sequence ,of a-b-c determine: a) Line currents. b) the readings of wattmeter W1 and W2 c) the impedance equivalent of the load in delta that can replace the induction motor
Non-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and blue phases respectively of 3-phase, 4 wire . The line voltage is 400. If a three phase motor is now started ,taking 150 A from the lines at a power factor of 0.3 lagging What should be the total current in each line and the neutral wire? Find the total real and reactive power supplied to the loads
A line voltage of 208 V is connected to a balanced three-phase delta-connected inductive load consisting of a phase resistance of 8 ohms in series with an inductive reactance of 6 ohms. Determine the phase current, the line current, the total power consumed and the kilovoltampere input.
A balanced load of phase impedance 100 ohms and power factor 0.8 is connected (a) in star ,and (b) in delta ,to a 400V, 3 phase supply calculate the power dissipation in each case
Two single-phase loads are connected in parallel, where load 1 is 4.7 kVA at 0.87 lagging power factor, and load 2 is5.2 kWat0.79lagging power factor. The load combination is connected to a voltage source of220VAC,50 Hz. a) Find the total complex power
A Y-Y three-phase circuit is shown below. Solve for the following: Line current of phase b = ? A Average power delivered to the load = ? W
The load connected to a 3-phase supply comprises three similar coils connected in star. The line currents are 22 A and the kVA rating and power input are 25 kVA and 12 kW respectively. (a) Find the line and phase voltage. (b) If the coils are now connected in delta to the same three phase supply, calculate the line current and phase current
A three phase transmission line has a resistance of 10 Ω and reactance of 80 Ω per wire. The load current is 90 A and the power factor of the load is 80% lagging. The sending (generator) end voltage in the line is 44,000 V line to line. What is the receiving end voltage? a. 38.4 kV b. 34.3 kV c. 41.2 kV d. 42.3 kV
a single phase transmission line is delivering 500kva load at 2kV It resistance 0.2ohm and inductive reactance 0.4ohm. Determine voltage regulation if the load power factor is 0.707 lagging
A 3-phase motor is rated at 100VA 0.9pf lag when operated with 100V 60Hz. The motor must be operated within 95-105V only. There is also an existing 100V 60Hz 3-phase generator set to be tested and verify if it can power the motor. There is a 3-phase connector with 15A rating per line that can be used. Computing for the expected per phase impedance values assuming that the motor is a wye-connected load, what is the per phase impedance of the motor modeling it as a wye-connected load?
delta-connected circuit having a load of resistance 12Ω and 31.83mH in series issupplied by 3 , 40030 V, 60Hz. Find the line currents assuming abc phasesequence
Determine the line current of a Y-connected balanced three-phase load, consuming 300 kW at power factor = 0.8 lagging and operating at 480 V. Work on PER UNIT with Sbase = 375 kVA and Vbase = 480V. Choose the best answer.