02: A three port network that is completely characterized at the same frequency (f) by the following ScatteringChart)Matrix:S₂20 V₂V = V₁ Ss 1512[0.0 0.2 0.510.0 0.20.5L0.5 0.5 0.01An open circuit is attached to port 2 while a matched load is attached to port 3(a) Find the reflection coefficient at port 1:₁ = V01=S₁1V01(b) Find the transmission coefficient from port 1to port 2: T21 = VozV01VI

Solution:Given Data:Three Port network:Find :Here find Reflection Coefficient Port 1 and…

A three port network that is completely characterized at the same frequency (f) by the following Scattering Matrix: V₁ = V₁ V₂ VS₁ + V₂5.- [0.0 0.2 0.51 0.5 0.0 0.2 0.5 0.03 10.5 An open circuit is attached to port 2 while a matched load is attached to port 3 (a) Find the reflection coefficient at port 1:₁ = = VI (b) Find the transmission coefficient from port Ito port 2: T21 = VOR

A three port network that is completely characterized at the same frequency (f) by the following Scattering Matrix: V₁ = V₁ V₂ VS₁ + V₂5.- [0.0 0.2 0.51 0.5 0.0 0.2 0.5 0.03 10.5 An open circuit is attached to port 2 while a matched load is attached to port 3 (a) Find the reflection coefficient at port 1:₁ = = VI (b) Find the transmission coefficient from port Ito port 2: T21 = VOR

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

At a frequency of 4 MHz a parallel wire transmission line has the following parameters: R = 0.025 Ω/m, L = 2 µH/m, G = 0, C = 5.56 pF/m. The line is 100 meters long, terminated in a resistance of 300 Ω. Find the characteristic impedance, standing wave ratio and voltage reflection coefficient of the load.
An optical fiber link with a distance of 30km long has a loss of 0.3dB/km. a) Calculate the minimum optical power level that must be launched into the fiber to maintain an optical power level of 3.0W at the receiving end.b) Estimate the required input power if the fiber has a loss of 0.6dB/km.c) Differentiate, with the aid of diagrams, the types of these dispersions and its effect on the transmission distance. (i) Modal Dispersion(ii) Chromatic Dispersion(iii) Polarization Mode Dispersion
As a technician, you are responsible for the construction of a 10km optical communication link between Pelonomi Hospital and National Hospital in Bloemfontein. The following link specifications are available:Transmitter output power: 15mWCommercially available optical cable length: 2kmOptical cable attenuation: 1.2dB/kmSplice attenuation: 0.1dB/kmLight transmitter-to-cable loss: 1.5dBCable-to-photo detector loss: 1.5dBSafety margin: 7dB Determine the minimum receiver sensitivity in microwatts needed to reliably detect a transmitted signal.
The effective span of an antenna is 2.147 m2 at an operating frequency of 100MHz. The antenna has no conduction or dielectric loss. The input impedance of the antenna is 75Ω and it is connected to a 50Ω transmission line. Find the directionality of the antenna system. (The term "system" here refers to the effects of binding to the transmission line.) It will be assumed that there is no polarization loss.
A cellular radio transmitter has a power output of 3 W at 800 MHz. It uses an antenna with a gain of 3 dBi. The receiver is 5 km away, with antenna gain of 12 dBi. Ignoring feedline losses and mismatch, calculate (a) the EIRP in dBW (b) the free space path loss, (c) the power delivered to the receiver in W and dBm
11.a. A fiber link has a polarization mode dispersion of 4.2 ps/√km. The fiber link is 5 km. What's the total polarization mode dispersion in this fiber?A. 1.9 psB. 9.4 psC. 0.84 psD. 21 ps 11.b. A transceiver has an extinction ratio of 6 in a fiber link. What's the extinction ratio power penalty?A. 1.5 dBB. 7.8 dBC. 1.1 dBD. 6 dB
Multiple Choice directions: Circle the letter of the answers 7. This is a special microwave coaxial cable used in the lower microwave bands L, S, and C. a. Flexible coaxial b. All of the above c. Hard line cable d. Braided coaxial 8. The practical microwave region is in the vicinity of a. 1-10 GHz b. 1-20 GHz c. 1-300 GHz d. 1-30 GHz 9. In a hybrid ring, if the signal is applied at port 1, which port has no output? a. 3 b. 2 c. 1 d. 4 Note: Explanation is not needed just provide the correct answers for each number.
RF Microwaves: Why is the input impedance of port 2 equal to z^2 /2 ? I am so confused. That looks like the input impedance for port 1. What is the input impedance of port 1 then ?
A transmitter supplied by 100W power is used with an antenna having a gain of 5dBi. a) Calculate the EIRP in dBm B) Calculate the power density (µW/m^2) at distance of 10km.
solve completely The internal resistance of the generator connected to the input of a transmission line is Zo = 75 ohms and operates at f = 3 GHz. The length of the transmission line is given as 31 cm. Calculate the impedance values seen while looking towards the load from the input side of this transmission line for the following two cases. a) ZL = 0 ohms b) ZL = infinite
At a frequency of 4 MHz a parallel wire transmission line has the following parameters: R-0,025 O/m. L-2 uH/m, G- 0, C5.56 pF/m. The line is 100 mcters long. terminated in a resistance of 300 Calculate the following i. Characteristic impedance of the line ii. Standing wave ratio iii. Voltage reflection coefficient of the load. iv. Recalculate the characteristic impcdance assuming the transmission line is lossless. V. Calculate the propagation constant of the linc B.
A 50 km communication line has the following parameters: series resistance (R) = 21.4 W/km series inductance (L) = 1.0 mH/km shunt capacitance (C) = 0.062 mF/km shunt conductance (G) = 0.868 mS/km The frequency is 796 Hz and the line is terminated to avoid reflection. If the power at the receiving end is to be –20 dB (6mW reference) and the sending end voltage is 362 V, determine the power at the sending end.