A torque of magnitude T = 1000 N·m is applied at D as shown. Shaft AB and CD have an elliptical cross- section. The major and minor diameters of shaft AB are 56 mm %3D and 50 mm, respectively. While the major and minor diameters of shaft CD are 42 mm and 38 mm, respectively. Determine the maximum shearing stress in each shaft. 40 mm T = 1000 N m D. 100 mm

A torque of magnitude T = 1000 N·m is applied at D as shown. Shaft AB and CD have an elliptical cross- section. The major and minor diameters of shaft AB are 56 mm %3D and 50 mm, respectively. While the major and minor diameters of shaft CD are 42 mm and 38 mm, respectively. Determine the maximum shearing stress in each shaft. 40 mm T = 1000 N m D. 100 mm

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
A shaft 100mm in diameter and 3m long, with bult-in ends, is subjected to a clockwise torque of 4KN-m applied 1m from the left end, and to another clockwise torque of 16 KN-m applied 2m fromthe left end. 16. Compute for the shearing stress at segment AB. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 17. Compute for the shearing stress at segment BC. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 18. Compute for the shearing stress at segment CD. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa
Determine support reaction at B . Given P=100 Kn L=10 m
The copper pipe [G = 5,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c = 8.0 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
A 5-m STEEL SHAFT ROTATING AT 2Hz HAS 70 KW APPLIED AT GEAR THAT IS 2m FROM THE LEFT END WHERE 20 KW ARE REMOVED.AT THE RIGHT END, 30KW ARE REMOVED AND ANOTHER 20 KW LEAVES THE SHAFT AT 1.5m FROM THE RIGHT END. (A) FIND THE UNIFORM SHAFT DIAMETER SO THAT THE SHEARING STRESS WILL NOT EXCEED 60 MPa. (B) IF A UNIFORM SHAFT DIAMETER OF 100mm IS SPECIFIED, DETERMINE THE ANGLE BY WHICH ONE OF THE SHAFTS LAGS BEHIND THE OTHER END. USE G = 83 GPa.
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
Compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 28000 kPa and 35000 kPa, respectively. The diameters are 6.35 mm for the pin, and 12.7 mm for the control rod. Assume single shear for the pin at B.
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
Compute the maximum force P in lb that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 3601 psi and 4820 psi, respectively. The diameters are 0.24inch for the pin, and 0.58 inch for the control rod. Assume single shear for the pin at B.
Compute the value of EIy at 2.5 m from the left support.
Determine the maximum horsepower a solid steel shaft 2.25in in diameter can transmit at 250rpm if the working stress in shear is 11,000lb/sq.in.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN