A transformer has 440 primary windings and 22 secondary windings. The potential difference across the primary coil is 100 V. The secondary coil is connected across a 125-ohm resistor. Find (a) secondary current (b) primary current. Hint: Use conservation of power. (c) effective load resistance of the SECONDARY COIL, which is connected across a 125 ohm resistor.

A transformer has 440 primary windings and 22 secondary windings. The potential difference across the primary coil is 100 V. The secondary coil is connected across a 125-ohm resistor. Find (a) secondary current (b) primary current. Hint: Use conservation of power. (c) effective load resistance of the SECONDARY COIL, which is connected across a 125 ohm resistor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.17P: The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of...

See similar textbooks

Similar questions

Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
1. A step-down transformer has a ratio of transformation of 10:1 and is connected to a 2,300- V, 60 hz ac supply. If the secondary load current is 40 A, calculate the, a) primary current, b) secondary voltage, c) power input, and d) power output. 2. A distribution transformer is connected to a 2,300 V, 60 Hz ac source with its primary windings equal to 1,200 turns. If the secondary voltage is 230 V, and the cross sectional area of the iron is 22.86 cm2 , calculate the a) mutual flux, b) maximum flux density, and c) number of secondary turns and the ratio of transformation.
A 72VA, 60Hz single-phase transformer has the equivalent circuit shown. (a) What is the no-load current if excited on the 120V side?(b) Estimate the losses in the transformer at full load with power factor 1.0.(c) Estimate the input voltage required for full load if the output voltage is 36V-rms and the output currentlags the voltage by 25 degrees.(d) What is the voltage regulation?Ans:(b) 4.68W (c)V_p = 123 angle(0.65) V rms (d) 2.5% Show me how each answer was found
A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the followingparameters: R, = 1.5 a, X, = 2.5 R, R, = 0.02 a, X, = 0.03 Q, R,, = 6 kR,and X,, = 8 kR. It is operating at 80% of its load at unity power factor.Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also sketch its phasor diagram.
A 2,300/240-V, 60-Hz, 4.6-kVA transformer isdesigned to have an induced emf of 2.5 V/turn.Assuming an ideal transformer, finda. The numbers of high-side turns Nh and low-sideturns Nl .b. The rated current of the high-voltage side Ih.c. The transformer ratio when the device is used as astep-up transformer.
1.The equivalent parameters of a 150kVA, 2400V/240V transformer, are R1=0.2Ω, R2=2mΩ, X1=0.45Ω, X2=4.5mΩ, Rc=10kΩ, and Xm=1.55kΩ. The transformer is operating at rated load and rated voltage with 0.8 lagging power factor. Using the approximate equivalent circuit referred to the primary side, determine: (i) (i) the voltage regulation (ii) (ii) the transformer power loss and efficiency 2.Nanoscale drives occur in the living world for example in the bacterial flagellum or ATP synthase. For one of these drives describe with the aid of diagrams how it operates and discuss the features which the drive has in common with large scale, man-made counterparts. 3.A 15 kW, 250V shunt motor with Ra=0.22 Ω, Rf=170 Ω. At no-load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full-load and rated voltage, the line current is 55A. What is the full-load speed?
A 120:480-V, 10-kVA step-up two-winding transformer is to be used as an autotransformer to supply a 120-V circuit from a 600-V source (a step-down autotransformer). When it is tested as a two-winding transformer at rated load, unity power factor, its efficiency is 97.9 %. 1.Show the connection diagram of the transformer converted as an autotransformer and identify which is the series winding Nse and the common winding Nc.
A 20-kVA 8000/277-V distribution transformer has the following resistances and reactance: RP = 32 Ω RS = 0.05Ω X P = 45Ω XS = 0.06Ω RC = 250 kΩ X M = 30 kΩ The excitation branch impedances are given referred to the high-voltage side of the transformer. (a) Find the equivalent circuit of this transformer referred to the high-voltage side. (b) Find the per-unit equivalent circuit of this transformer. (c) Assume that this transformer is supplying rated load at 277 V and 0.8 PF lagging. What is this transformer’s input voltage? What is its voltage regulation? (d) What is the transformer’s efficiency under the conditions of part (c)?
A transformer with a 10:1 ratio and rated at 60kVA, 2200/220V, 60Hz is used to step down the voltage of a distribution system. The low tension voltage is to kept constant at 220V. (a) What load Impedance connected to the low-tension side will be loading the transformer fully at 0.8 power factor (lag) ? (b) What is the value of this impedance referred to the high tension side?
1. a) Find the turns ratio N1/N2 for the ideal transformer in the circuitso that maximum average power is delivered to the 400 Ω load.2. b) Find the average power delivered to the 400 Ω load.3. c) Find the voltage V1.4. d) What percentage of the power developed by the ideal currentsource is delivered to the 400 Ω resistor?
A 200/100 V, single-phase transformer is rated 10 kVA. If this transformer is connected as an auto-transformer across a 50 V supply, what is the maximum output voltage that can be obtained from this transformer? If the load current is now 8 A, determine the kVA output.