A transformer iron core has a mass of 50 kg. At 25 Hz, the maiximum flux density in the core is 1.3 T. Assume a Steinmetz coefficient of 600 J/m3 and density of 7800 kg/m3. Find the energy lost in the core after 1 hour.

A transformer iron core has a mass of 50 kg. At 25 Hz, the maiximum flux density in the core is 1.3 T. Assume a Steinmetz coefficient of 600 J/m3 and density of 7800 kg/m3. Find the energy lost in the core after 1 hour.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11P: For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power...

See similar textbooks

Related questions

Q: Voice information with a frequency range of 0.3 - 4 kHz is sampled according to Nyquist requirements...

A: It is given that: fm=0.3~4 kHzL=256 levelsn=log2256=8 bitsd=0.5M=16

Q: If resistance is 10 Q and inductance is 5 H in an RL series circuit, then the time constant of this ...

A: Given, Resistance, R=10 Ω Inductance, L = 5 H

Q: Given a voltage v = 50 cos(200nt + 60°) V. Find (a) its amplitude, (b) its phase angle in degrees, (...

A: The solution is given below

Q: arithmetic operation: +15 - 6

Q: .Obtain the Fourier series of the function for the waveform shown in Figure 11.

A: The given signal is shown below:

Q: 2. Differentiate between magnetic force Fg experienced by a current carrying conductor and a free ch...

Q: Use Kirchhoff’s Laws to find the branch currents indicated in the following network: (Show detailed ...

A: The given circuit diagram is shown below:

Q: 3. How dose the bandwidth change in relation to increasing signal amplitude? FM

Q: Find V, the magnitude, A direclion of unknowh urrenti through 10, 52 4 20 istance resistors. 1. 15A4...

Q: Q3. Using the Laplace transform tables, find the Laplace transforms of the following functions for t...

A: Given function, ft=3 sin 5t+2 cos3t+6t3 for t>0

Q: (a) For the circuit shown in Figure Q4.1 the switch has been in position A for a long time before mo...

A: The solution is given below

Q: 5- prove that z transform of nu(n) zl>1 - 1)? z sin(a) 2- 22 cos(a) +1 sin(an)u(n) z|>1

Q: Determine Ib, lc, and Vce. (beta = 100)

A: The required parameters of the voltage divider biased CE amplifier circuit can be calculated by usin...

Q: El efecto del nivel de CD no es de peso en la escogencia de un código de linea Seleccione una: O Ver...

A: Line code: It is the process of making digital data into digital signals. The line code is represent...

Q: Unipolar line code corrects synchronization problems. true or false

A: Unipolar line code- Unipolar encode is a line code. The positive voltage represents 1 binary, and th...

Q: sequence components o

A: For PU system- PU value=Actual value/Base value

Q: Q2/ For A bridge shown, prove that C=1/ w² L, L= 1/ w°C, and f=1/2n LE R2

Q: < Notes Done How many GPS Satellites are present?

A: GPS satellie is used to circulate the earth it circulates the earth two times in a single day a uini...

Q: Answer the question briefly. 1. How to generate an AC? Explain. 2. What are the types of alternating...

Q: Theoretical calculations: 1. How can you draw the spectrum of FM?

A: MODULATION: It is the method of transmitting a signal through modulating high frequency carrier sig...

Q: 1.2 kW 0.8 KVAR (cap) 100/90° V 2 kVA 4 kW 0.707 pf leading 0.9 pf lagging

A: The solution is given below

Q: 1. Determine the (i) operating frequency and (ii) feedback fraction for Colpitt's oscillator shown i...

Q: Example 2: If I, = 0.8 A, and I, = 0.5 A, find the following: R1 52 + I3 + V, = 40 V + V2 R2 V3 R3 1...

A: The solution is given

Q: 1. Reduce to canonical form

A: The block diagram can be reduced by considering the cascade and parallel blocks and then reduce the ...

Q: [10] Draw a circuit with the following input/output table. [Note: Use only NOT, AND, and OR gates, a...

A: The solution is given below

Q: Which of the following is true about the collector current? it approximately equals the emitter curr...

Q: a Ix A,079( 2Vx 12 be HE 10 I3 I2 -jia I4 jia 12 2Ix Vx I1 e all

Q: *26. Design a self-bias network using a JFET transistor with Ipss a Q-point at values. IDe = 8 mA an...

A: Brief description : Junction field effect transistors are having main advantage is that it will prov...

Q: 4. Show that for all R>0, C>0, and w>0, the power factor of a series RC circuit and of a parallel RC...

A: Power factor: It tells how much active power is utilized by the circuit from the apparent power.

Q: Find the Norton equivalent for the circuit shown in Figure 2.55(a) O. R 20 n 15 1 R3 50 a-40 (a) Ori...

Q: diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms) so...

Q: NAnsver all the questions (1) The rms value of the input voltage for a bridge network is shown in th...

A: We need to analyse the given diode network

Q: The tunneling current depen between the last atom of the tip and tH Select one: O True O False

A: Answer: True

Q: 23. A supply of 240V, 50Hz is connected across a pure inductance and the resulting current is 1.2A. ...

A: The solution is given below option A is correct

Q: usna.blackboard.com/webapps/assessment/take/launch.jsp?course_assessment_id- 162584 1&course_id=_692...

A: The solution is given below

Q: Determine I and V on the Circuit +3 v oD +2 v +1 Vo 1 kn

A: The solution is given below

Q: 1) A 230-V, 50-Hz, 6-pole, single-phase induction motor has the following constants. = 0.12 2. r, = ...

Q: 4- Find z_ transform for each of the following signal 1)x (n) = (n + 1)a "u (n ) 2 ) x (n ) = [3(2 )...

Q: Theoretical calculations: 3. How dose the bandwidth change in relation to increasing signal amplitud...

Q: Determine the following when it is subjected to a waveform shown below: a) The first five non-zero t...

A: Given the circuit, as shown below: Given the input signal as shown below: a) We need to determine ...

Q: Fig.(4-7) 2. Which side the filter is select (upper or lower)? Explain that? 4. What is the applicat...

A: We need to tell about SSB modulation

Q: Main Circuit Diagram: A. Vs R33 RL lov B.

Q: 2. Use mesh-current analysis to find the branch currents indicated in the networks shown below.

A: Follow the numbering in circuit and for equations

Q: Determine the periodic time with given frequency of 2.5Hz A. 0.4s B. 0.04s C. 40us D. 100ms

A: The solution is given below

Q: 4] Write 3810 in binary notation.

A: It is the decimal number To convert it into binary we need to divide it with 2

Q: 10 : 1 D4 115Vrms v, 60HZ 50µF c R$2.2k +

Q: Find the phase angle between i =-4sin (377t +25.) and i2 = 5cos(377t -40-). 155 degrees. 115 degrecs...

Q: A magnetic circuit consists of silicon steel of 3000 permeability, of 10 cm length and a 2 cm air ga...

Q: Theoretical calculations: 3. How dose the bandwidth change in relation to increasing signal amplitud...

Q: Given KG(s)H(s) = K+0.3 2s+3) plot the root loci. What is the value of K and the values of two other...

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
A small single-phase 60 Hz transformer has 10.2 W at no load. The core has a volume of 750 cm3. The maximum flux density is 10,000 G and the hysteresis constant of the core is 0.0005. Using the Steinmetz law on hysteresis loss, find the eddy current loss.
3 In a Ideal transformer (assuming no losses), the no load current I0 is in phase with the magnetic flux. Select one: True False