A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If the tree has a mass of 3 tonne (i.e. 3 metric ton), for the position shown 180 1080 2250 2040 720 Determine the bar the pressure in hydrauliç cylinder AB. Answer:

A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If the tree has a mass of 3 tonne (i.e. 3 metric ton), for the position shown 180 1080 2250 2040 720 Determine the bar the pressure in hydrauliç cylinder AB. Answer:

Name: A tree feller cuts off large tree near the ground level and then cont
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If the tree has a mass of 3 tonne (i.e. 3 metric ton),for the position shown180CB108022502040720Determine the bar the pressure in hydrauliç cylinder AB.An

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Determine the smallest distance I) that would prevent the concrete dam from tipping about corner A. Use w=62.4lb/ft3 for water and c=150lb/ft3 for concrete.
One end of a rod of length L and density ρ is fixed by a frictionless pivot at a depth d under water. Determine the equilibrium positions of the rod in terms of its angle α measured from the vertical, and the investigate whether the equilibrium positions are stable or unstable, given that (a) ρ = 500 kg/m3 ; (b) ρ = 853 kg/m3 (The density of water is ρw = 1000 kg/m3 .)
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 581 kN. Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.
Cords are looped around a small spacer separating two cylinder each weighing 400kn and pass over a frictionless pulleys to weights of 200KN and 400kn. Determine the angle and the pressure N between the cylinder and smooth horizontal surface