A trough with a trapezoidal cross-section, as shown in the figure, contains vegetable oil with density 940 kg/m3. (Use g = 9.8 m/s2 for the acceleration due to gravity.) 3 m 2 m 5 m 1 m A trough has a trapezoidal cross section. The vertical side is 3 m in height. There are two horizontal sides perpendicular to the vertical side, with the larger horizontal side being at the top and 2 m long, and the shorter side at the bottom is 1 m long. The width of the trough is 5 m. (a) Find the hydrostatic force (in N) on one end of the trough if it is completely full of oil. N (b) Compute the force (in N) on one end if the trough is filled to a depth of 1.8 m. (Round your answer to two decimal places.) N

A trough with a trapezoidal cross-section, as shown in the figure, contains vegetable oil with density 940 kg/m3. (Use g = 9.8 m/s2 for the acceleration due to gravity.) 3 m 2 m 5 m 1 m A trough has a trapezoidal cross section. The vertical side is 3 m in height. There are two horizontal sides perpendicular to the vertical side, with the larger horizontal side being at the top and 2 m long, and the shorter side at the bottom is 1 m long. The width of the trough is 5 m. (a) Find the hydrostatic force (in N) on one end of the trough if it is completely full of oil. N (b) Compute the force (in N) on one end if the trough is filled to a depth of 1.8 m. (Round your answer to two decimal places.) N

Name: A trough with a trapezoidal cross-section, as shown in the figure, con
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A trough with a trapezoidal cross-section, as shown in the figure, contains vegetable oil with density 940 kg/m3. (Use g = 9.8 m/s2 for the acceleration due to gravity.)3 m2 m5 m1 mA trough has a trapezoidal cross section. The vertical side is 3 m in

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

(a)

Find the hydrostatic force (in N) on one end of the trough if it is completely full of oil.

(b)

Compute the force (in N) on one end if the trough is filled to a depth of 1.8 m. (Round your answer to two decimal places.)

A trough with a trapezoidal cross-section, as shown in the figure, contains vegetable oil with density 940 kg/m³. (Use g = 9.8 m/s? for the acceleration due to gravity.)
F2 m -
3 m
5 m
1 m
(a) Find the hydrostatic force (in N) on one end of the trough if it is completely full of oil.
(b) Compute the force (in N) on one end if the trough is filled to a depth of 1.8 m. (Round your answer to two decimal places.)
N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular gate of width "a", length "b" and inclined at an angle "A", with water on one side is shown in the figure. Use a=9.5 ft, b=5ft, z=6.5ft and angle A=55 degrees. (a) Determine the location of the center of the gate from the water surface along the plane of the gate (in feet). (b) Determine the eccentricity (in feet). (c) Determine the location of the center of pressure from the water surface along the plane of the gate (in feet). (d) Determine the vertical distance (in feet) of the center of the gate from the water surface. (e) Determine the total resultant force (in lb) acting on the side of the gate.
In Fig., gate AB is 5 ft wide into the paper, and stopB will break if the water force on it equals 9200 lbf. Forwhat water depth h is this condition reached?
Water in a tank is pressurized to 140 cm Hg, as shown in the figure. Determine the hydrostatic force per meter width on panel AB.
A vertical dam has a semicircular gate as shown in the figure. The total depth d of the figure is 24 m, the height h of air above the water level is 4 m, and the width w of the gate is 4 m. Find the hydrostatic force against the gate. (Round your answer to the nearest whole number. Use 9.8 m/s2 for the acceleration due to gravity. Recall that the mass density of water is 1000 kg/m3.)
An underwater gate 8 m wide is held closed by a force, F, as shown in the figure. If the force is applied at the middle of the gate, what is the minimum value required to keep the gate closed? take density of water= 996kg/m3
A conical vessel r=(b-z)tanA, rests with its open end downward on a flat surface, as shown in the figure. We want to fill it to a height h with a liquid of density p. What will be the lifting force on the vessel? (tanA: tangent of A)
Note: Please state what formula you are using. And please be clear and detailed with your solution. Atleast explain. It will help me, thanks. Problem: A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45o from the vertical with vertex pointing upward. The base of the gate is 2.70 m below the surface of oil (s = 0.80). What normal force must be applied at the vertex of the gate to open it? Show figure
example 1.A 30-m long dam retains 9m of water as shown in the figure. Find the total resultant force acting on the dam and the location of the center of pressure.
3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Include also the free body diagram or figure of the problem, and your findings after solving it.
2. Estimate the vacuum pressure that should be created by a suction pump in order to lift a ground water which is 10m below the level ground. Neglect the effect of pipe friction. Draw the figure or free body diagram, and explain its step by step solution. 3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Draw the figure or free body diagram, and explain its step by step solution.
Q3)A tank 6 m long 3 m wide and 2 deep contains oil to depth of 1.75 m .If it accelerated horizontally at 2.5 m/s2 in the direction of its length. How muchı oil would spill out and the acceleration force.
The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover is D = 4 m. Find the magnitude of the applied force (Fa) as shown. Take the density of water as 999kg / m3.