A truck and trailer combination with the axle loads shown in the figure rolls across the simply supported 12 m span. Validate the position of the resultant R from the 15 kN load. Compute the (a) maximum bending moment (b) maximum shear force FEE 15 kN 125 kN IR 90 kN |50 kN -3m -2 m B -3m -6 m R 12 m 1R2

A truck and trailer combination with the axle loads shown in the figure rolls across the simply supported 12 m span. Validate the position of the resultant R from the 15 kN load. Compute the (a) maximum bending moment (b) maximum shear force FEE 15 kN 125 kN IR 90 kN |50 kN -3m -2 m B -3m -6 m R 12 m 1R2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the beam shown in Figure P12.46 with- out the 80 kN load. Construct the envelope of maximum positive shear assuming the beam supports a 6 kN/m uni- formly distributed load of variable length.
A truck with axle loads of 20KN and 30KN on a wheel base of 2.5m rolls across a 5-m span. A. If the center of the 30kN axle load and the resultant load is at the center of the beam, calculate the reaction at the right & left support. B. Compute the maximum & minimum shear force. C. Compute the distance of the resultant load from the 30kN axle load. A simply supported beam of length L is load with a moving load concentrated P passing across the span of the beam. Determine the location of P from the left support that will cause maximum moment in the beam.
For the beam and loading shown, specify (a) the absolute value of the reaction force in B in units |RB| kN, (b) the absolute value of the displacement at the midpoint D of the BC part of the beam in units |yD| mm. Take the P value in the question 15 kN and the W value 34 kN/m. E = 200 GPa and I = 34.4 x 10-6 M4.
A 6-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point loads 15 kN at 1.5 m from both ends. If E = 200 Gpa and I = 0.000332 m4 , determine the following using Moment Area by Parts: a.) Midspan deflection b.) Deflection at 1.5 m from the left reaction.
the mobile crane (weight =48 kN) moves across the brige of length, l =14m. the front wheels of the mobile carry the three-quarter of its weight while the rear wheels carry a quarter of its weight. iif the distance between front and rear wheel is b = 0.7m. Determine themaximum value of bending moment as it moves across
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
For the simple beam with overhang shown, draw the infuence line for the following: a) Vertical reaction at A b) Shear at C c) Moment at C What is the maximum negative moment at C due to a concentrated live load P = 27.5 kN and a uniform live load with intensity w = 12 kN/m? Show using a sketch where the loads shall be applied to obtain the maximum value.
Shaft of constant stiffness, round section, left edge of which is rigidly fixed in section A, is loaded with concentrated moment M in sections B (M = 20 kN·m). To determine the minimum torque value Mx in the section D.
The steel framework as shown in Figure Q1 is used to support the 200 mm reinforced stone concrete slab that carries a uniform live loading of 14 kN/m2. Sketch the loading that acts along members BE and FED. Set a = 9 m and b = 12 m.
A reinforced concrete beam has a width of 425mm and an effectivedepth of 900mm. The longitudinal bars at compression side are 4-25mm dia. and 2layers of 4-32mm dia. at tension side. Concrete strength f’c=27.60 MPa and fy=420.4) Calculate the Transformed moment of Inertia.5) Calculate the moment capacity of the section.6) Calculate for the safest uniform load that can carry by the beam if ihas a lengthof 10m.
A W10 × 60 A992 steel column is 16 ft tall with translation and rotation fixed at both ends of thecolumn and for both axes. The column supports a concentric axial dead load of 13 kips and a concentricaxial live load of 39 kips. There is no moment about the y-axis. Take the lateral-torsional bucklingmodification factor as Cb = 1.0. Which of the following is most nearly the maximum moment that canbe placed on the x-axis? (LRFD options are in parentheses.) Choose the correct answer. (A) 133 ft-kips (220 ft-kips)(B) 142 ft-kips (237 ft-kips)(C) 150 ft-kips (257 ft-kips)(D) 166 ft-kips (280 ft-kips)
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?