A truss joint shown consists of a bottom chord C made up of two angles, and web members A and B each carrying the given loads. Determine the magnitude of the resultant and its inclination with respect to the horizontal. Locate the resultant in the given figure. 150 kN 9.5mm Gusset plate 2 ang les 220 kN 2 angies 70% 624.67 38 400 kN kN C 2 angles

A truss joint shown consists of a bottom chord C made up of two angles, and web members A and B each carrying the given loads. Determine the magnitude of the resultant and its inclination with respect to the horizontal. Locate the resultant in the given figure. 150 kN 9.5mm Gusset plate 2 ang les 220 kN 2 angies 70% 624.67 38 400 kN kN C 2 angles

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular reinforced concrete beam with width of 300 mm & effective depth of 600 mm is subjected to a service bending moment of 200 kN.m. The beam is reinforced with 4-32 mm diameter bars. n = 8. 1. Compute the distance kd? a. 246.33 mm b. 353.67 mm c. 170.33 mm d. 302.33 mm 2. Which of the following gives the moment of inertia about N. A.? a. 4173.81 x 106 mm⁴ b. 3471.81 x 106 mm⁴ c. 4371.81 x 106 mm⁴ d. 4713.81 x 106 mm⁴ 3. Which of the following most nearly gives the maximum stress in steel in Mpa? a. 100 b. 110 c. 120 d. 130
The shorter legs of two 6”x 4” x 1⁄2” angles arewelded to a 12”-20.7-lb channel. Determine themoments of inertia of the combined sectionwith respect to centroidal axes respectivelyparallel and perpendicular to the web of thechannel. For the 12”-20.7-lb channel, its area is 6.03 sq. in.; x̄=0.70; ȳ=0; web thickness t = 0.280"
20 -In the cantilever beam in the figure, bar clearance L= 225 cm and single load acting on the free end of the bar P = 12 kN. The cross-sectional effects at point B will be calculated. Accordingly, the Moon on the fixed support at point A=? A) None.B) 27000C) 12000D) 0E) 9000
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
(a) Compute the vertical deflection at C, the horizontal deflection at D and the rotation at A by the virtual work method. (b) If support E moves to the right by 5mm and settles downward by 10mm, compute the additional horizontal deflection at D. Given E=200GPa and I=108mm4 .
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, θ = 32°, θ˙ = 47 deg/s, and θ¨ = 21 deg/s2. Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.3-kg slider B. Neglect all friction, and let L = 0.64 m. The motion occurs in a vertical plane.
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
may i know why did you use the 35 kN twice and not the 70kN? also, why is the moment at A = 0?
Determine the solution for the bar forces in the truss shown when P = 1 kip and x = 5 ft: AC = -1732.05 AB = 2000 BC = -866.03 BD = 2500 DC = 2020.73 EC = -3175.43