A two-core feeder 182 kilo meter long supplies a maximum current of 167 A at 400 volts. The demand is such that the copper loss per annum is that which would be produced by the full load current flowing for 10 months. The resistance of conductor 1 km long and Imm? section of conductor as 0.0401 ohm. The value of area of cross section is 117.5 mm?. The cost of energy is 15 baisa per unit. Find the power loss and Annual cost. Power Loss = kW Annual cost = Rial

A two-core feeder 182 kilo meter long supplies a maximum current of 167 A at 400 volts. The demand is such that the copper loss per annum is that which would be produced by the full load current flowing for 10 months. The resistance of conductor 1 km long and Imm? section of conductor as 0.0401 ohm. The value of area of cross section is 117.5 mm?. The cost of energy is 15 baisa per unit. Find the power loss and Annual cost. Power Loss = kW Annual cost = Rial

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

A high-voltage power line is made of aluminum conductor steel reinforced (ASCR) material. Suppose a power line has a radius of 2.00 mm and assuming the resistivity of the ACSR is 23.50 x 10^-9 resistor x m, how long is this powerline if it dissipates (on average) 350 MW with a maximum voltage across the powerline of 345,000 Volts (DC)?
5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential
What's the primary disadvantage of using copper conductors? A. WeightB. DurabilityC. Cost D. Availability
A two wire DC distributor AB, 1000 meter long, is supplied from both ends, 240 V at A and 242 V at B. There is a concentrated load of 200 A at a distance of 400 meter from A and a uniformly load 1.0 A/m between the midpoint and end B. Determine (i) the current fed at points A and B (ii) the point of minimum potential and (iii) voltage and this point. Consider cable resistance as 0.005 ohm per 1000 meter each core.
(a) Give the condition for the loss of load in a power generation system in terms of outages in generation units (b) Give the assumption taken for the calculation of LOLP? [Write relevant Answers in 1 or 2 sentences in each part)
A motor,the input to which is 20kW at 220V,is supplied by a two-core cable.400m long.If the power lost in the cable Is not to exceed 5% of the motor Input . Calculate the minimum permissible C.S.Area of the cable conductor What will be the voltage at the feeding point ? Assume the resistivity of the conductor at working temperature to be 0.02 microohm/m
A 415 single core cable has a conductor diameter of 0.5 cm and a sheath of inside diameter 3 cm. In cable insulation, find: (i) minimum stress (in V/cm); (ii) maximum stress in (V/cm); (iii) Describe where these minimum and maximum stress will occur in cable insulation?; (iv) Suggest what should be the minimum dielectric strength (in V/mm) of the cable insulation to avoid any breakdown of the given cable
Discuss the challenges of Renewable Energy
Discuss the importance of renewable energy.
In your own words, define a. an ideal conductor; b. an ideal voltage source; c. an ideal current source.
Electrical Distribution systemsvoltage drop and power loss chapter
Discuss how can you avoid the reverse power flow from battery to PV module in night?