A uniform slender rod is connected to a thin plate as shown. The rod has a weight of 10lb and the plate has a weight of 15lb. A CCW angular velocity of 12 rad/s is applied to the system. What is the angular acceleration of the system and the reactions at point C? Note: for a composite system, the COM location from the point of interest (y_bar) is: ybar={Eyelemental*m}/Em M = 6N*m 0.4 m 0.4 m 0.5 m 0.7 m 0.3 m

A uniform slender rod is connected to a thin plate as shown. The rod has a weight of 10lb and the plate has a weight of 15lb. A CCW angular velocity of 12 rad/s is applied to the system. What is the angular acceleration of the system and the reactions at point C? Note: for a composite system, the COM location from the point of interest (y_bar) is: ybar={Eyelementalm}/Em M = 6Nm 0.4 m 0.4 m 0.5 m 0.7 m 0.3 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.15P: In Sample Problem 5.5, determine Oy with one scalar equilibrium equation.

See similar textbooks

Similar questions

Question 4For the dynamic system shown in the figure,derive the equations of motion using Lagrange’s equations.
7The total sleeve movement in a Hartnell governor is 3 cm. The mass of rotating balls is 1.5 kg each. At the mid position of the sleeve arm, which is 6.5 cm long, is horizontal. The ball arm has a length of 7.5 cm. At the mid position of the sleeve, the balls rotate at a radius of 10.5 cm. Due to the mal adjustment of spring, the equilibrium speed of governor at top position is 415 rpm and In lowest position it is 430 rpm. Determine (1) Stiffness and initial compression of spring. (ii) Required initial compression in spring which gives equilibrium speed at the topmost position which is rpm more than the lowest position neglect bliquity.m = 1.5 kg
A solid cylinder (mass 1.2kg, radius 5.0cm) on a horizontal table is connected to a block (mass 200 g) via a pulley (mass 0.80kg, radius 10.0cm) via a light, rigid string. Draw free body diagram for each of the object 1) list the dynamic and kinematic equations that related to all three objects. 2) find the acceleration of the falling block 3) fnd the angular acceleration of the cylinder and the friction force on it
A rotating disc of 2m diameter has two eccentric masses of 0.6kg each radii of 60mm and 70mm at angular positions of 00 and 1500, respectively. A balancing mass of 0.1 kg is to be used to balance the rotor. What is the radial position of the balancing mass?
Consider two robot-manipulators:• A SCARA robot with joints displacement range q1,2 = −90◦...90◦ and q3 = 0..10cm and links lengths L1,2=10 cm.• A Cartesian robot with joint displacements’ range q1,2,3 = 0..10 cm.Which statement is correct?1) The Cartesian robot has a larger workspace.2) It is not possible to judge the workspace based on the information provided.3) Both robots have revolute joints.4) The SCARA robot has a larger workspace.
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
The geared system shown in the figure below represents an elevator system. The motor has an inertia I1 and supplies a torque T1. Neglect the inertias of the gears, and assume that the cable does not slip on the pulley. Identify an expression for the equivalent inertia Ie felt on the input shaft (shaft 1). Then identify the dynamic model of the system in terms of the speed ω1 and the applied torque T1. The pulley radius is R.
Determine the manipulator linear and angular velocity for the 3-DOF articulated armusing Jacobian modelling
Figure 13 shows a simple model of a machine part, with an applied moment applied clockwise to the disc. The disc rotates without translation. Assume that the mass is on a frictionless surface and also that the disc rotates around the shaft with no friction effects. (a) Determine the kinetic and potential energy of the system. (b) Determine the equation of motion of the system using Lagrange’s equation.
Model the following system by writing the two equations of motion for the double-pendulumsystem shown in the figure below. Assume the displacement angles of the pendulums are smallenough to ensure that the spring is always horizontal. The pendulum rods are taken to be mass-less, of length l, and the spring is attached a distance of d down the length of the rods.
The uniform bar shown has mass m, length l, and mass momentof inertia I about its mass center. The bar is supported by two springs k1and k2, as shown in the figure. Obtain the differential equation of motion anddetermine the natural frequency of the system in the case of small oscillations. (USE VIRTUAL WORK METHOD)
Determine the degrees of freedom by constructing the mechanisms belonging to the given kinematic chain.