A unity Feedback system is characterized by open loop transfer function G(s) = K / S(S+40) %3D The system is having a damping ratio of 0.5. Determine the following. The value of gain K is : Natural frequency of Oscillation w, is: Rise time in seconds is : Peak time in seconds is : Peak overshoot in percentage is :

A unity Feedback system is characterized by open loop transfer function G(s) = K / S(S+40) %3D The system is having a damping ratio of 0.5. Determine the following. The value of gain K is : Natural frequency of Oscillation w, is: Rise time in seconds is : Peak time in seconds is : Peak overshoot in percentage is :

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

A unity-feedback system has forward transfer function (see attached). a) Sketch the root locus for this system as K varies from 0 to ∞; b) Use the Routh-Hurwitz test to determine the range of K for the system to be stable; show this value of K on the root locus plot.
A For a monolithic negative feedback system defined by the open path function, find the gain range (to operate the system at steady state
Since G(s) is the transfer function of the system, draw the root locus of the closed-loop system with negative unit feedback below, clearly stating each step. (Root locus plots drawn using any program such as Matlab etc. will not be considered)
The unit in the figure below is given as G (s) in feedback system. When a unit ramp is applied to the input of the system, the steady-state error is 0.4% and when the unit step is applied to the input, the settlement time is desired to be 50 ms. So which of the following is a pole value of the closed-loop transfer function? G(s)=k/s(s+a)
The transistor parameters for the circuit shown are VTN = 0.4 V, Kn =0.5 mA/V2, and λ = 0.(a) Discuss the feedback topology, show the input ant output connections (series orshunt)(b) Find the feedback factor β (find the transfer function without feedback first)
The circuit as shown is a shunt-shunt feedback amplifier. Use feedback analysis to find the midband input resistance, output resistance, and transresistance of the amplifier if RI = 500 Ω, RE = 2 kΩ, β0 = 100, VA = 50 V, RL = 5.6 kΩ, and RF = 47 kΩ, when vi and RI are replaced by a Norton equivalent circuit. What is the voltage gain for the circuit as drawn?
(Q1)An uncompensated unity feedback system with certain deficiencies has no zeroes and poles at -1, -2 and -5. Answer the following questions based on the above description of the system Determine using an apt technique, the gain of the system at damping ratio 0.45 Include a series compensator to the uncompensated system with zero at -0.0111 and pole at -0.01.
Given a unity feedback system with G (s) =K/ s (s+4). What is the value of K for a damping ratio of 0.5?
Consider the unity-feedback control system with the following feedforward transfer function: G(s) = K / s(s2+4s+5) (1) Plot the root locus. (2) Determine closed-loop poles that have the damping ratio of 0.5. Find the gain value K at this point. (3) For what value of K is the overshoot less than 10% and the maximum rise time less than 1.5s.
Ex. 840. A proportional controller, Kp, is desired for the plant 1/( (s) (s+ 7) (s+12) ). Design the unity feedback system so that the dominant poles indicate a closed loop step response with a 32% overshoot. What is Kp, zeta, wn, wd, Ts, Tp, velocity constant (Kv) and the resulting SS error for a ramp input, and the gain, Kp, for marginal stability. MATLAB is not required.
An op amp has a dc gain of 100 dB and a unity-gain frequency of 10 MHz. What is the upper-cutoff frequency of the op amp itself? If the op amp is used to build a noninverting ampliﬁer with a closed-loop gain of 60 dB, what is the bandwidth of the feedback ampliﬁer? Write an expression for the transfer function of the op amp. Write an expression for the transfer function of the noninverting ampliﬁer.
An op amp has a dc gain of 100 dB and a unity-gain frequency of 10 MHz. (a) What is the bandwidth of the op amp? (b) If the op amp is used to build a noninverting ampliﬁer with a closed loop gain of 60 dB, what is the bandwidth of the feedback ampliﬁer? (c) Write an expression for the transfer function of the op amp. (d) Write an expression for the transfer function of the noninverting ampliﬁer.