A V sine The supply voltage V = 120230° volt. Load A is 4 KVA at power factor 0.8 leading. Load C is an inductive load with active power 1 KW and reactive power 500 VAR. Load B is 2400 VA at power factor 0.6 lagging. RMS value of the current drawn from the voltage source is Ampere Phase of the current drawn from the voltage source is Radian

A V sine The supply voltage V = 120230° volt. Load A is 4 KVA at power factor 0.8 leading. Load C is an inductive load with active power 1 KW and reactive power 500 VAR. Load B is 2400 VA at power factor 0.6 lagging. RMS value of the current drawn from the voltage source is Ampere Phase of the current drawn from the voltage source is Radian

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
The power factor for an inductive circuit (R-L load), in which the current lags the voltage, is said to be (a) Lagging (b) Leading (c) Zero
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
An industrial load is driven from a single phase supply at 91 V. Load current is 6 A. Power Factor is 0.651 lagging. What value of Q of Power Factor Correction capacitors are needed to be added to bring the Power Factor to 1.00? Result should be in VARs, magnitude only (no sign)
In the circuit in the figure, there is a load consisting of the series connection of the resistor R0 and the inductance L0 between the terminals a and b. The amplitude of the voltage Vs (t)√2 is 150 volts, the phase angle is 0s = 0 degrees, the period is T = 200π microseconds. Since R = 300ohm and C = 1μF;a) Find the R0 and L0 values that enable the load to draw the maximum average power from the circuit.b) Calculate the complex power on the load.
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6.The L2 load draws 6 kVA with a leading power factor of 0.8.According to this; How many amperes (rms) is the Is current?
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; How many amperes (rms) is the Is current?
A residential four-wire system supplies power at 220 V rms to the following single-phase appliances: On the first phase, there are ten 60-W bulbs. On the second phase, there is a 1-kW vacuum cleaner with a power factor of 0.9. On the third phase, there are ten 23-W compact fluorescent lamps with power factor of 0.61. Find a. The current in the neutral wire. b. The real, reactive, and apparent power for each phase.