A Venturi meter having a throat diameter of 150 mm is installed in ahorizontal 300-mm-diameter water main, as shown. The coefficient ofdischarge is 0.982. Determine the difference in level of the mercury columnsof the differential manometer attached to the Venturi meter if the discharge is142 L/s.Ans: h= 255 mm

Answered: Image /qna-images/answer/afdc4a39-5e74-4e0c-8802-24efb7b383ca.jpg

Answered: A Venturi meter having a throat…

A Venturi meter having a throat diameter of 150 mm is installed in a horizontal 300-mm-diameter water main, as shown. The coefficient of

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. Determine la fuerza en cada miembro e indique si la miembros están en tensión o compresión. 4 kN…

A: Calculate force in each member of truss?

Q: Try solving the following practice problem: The unconfined compression test was carried out on a…

A: Given Diameter of sample= 40 mm Length= 80 mm

Q: Describe Lithosphere

A: To Describe: Lithosphere

Q: Given data : Void ratio=0.332 Find porosity

A: Introduction : The given question is related with geotechnical engineering . In this question we are…

Q: A direct shear test, when conducted on a remolded sample of sand, gave the following observations at…

Q: bed of sand 12 m thick is underlain by a compressible stratum of normally loaded clay, 6 m thick.…

Q: A Problem Number 4: Determine the Reactions on the supports of the Loaded Beams. A) RA= KN, R₂ = KN…

Q: clay stratum is 4.5 m thick and rests on a rock surface. The coefficient of consolidation of a…

Q: Calculate the discharge through the submerged orifice shown in the figure. Ans: 109 lit/sec 50 kPa…

Q: Problem Number 2: In the given flexible cable set-up carrying a uniformly distributed load spread…

Q: A clay layer 5 m thick has double drainage. It was consolidated under a load of 127.5 kN/m2. The…

Q: Q8) A fountain ejects water through a nozzle, which have inner diameters of 0.3 mm, at B as shown.…

A: Given-

Q: If an object is a square, then it has four sides. If j is a square, then j has five sides. For all…

A: Square ia figure which has 4 sides of equal length The quadratic equation has 2 roots Those 2…

Q: In the given flexible cable set-up carrying a uniformly distributed load spread horizontally has a…

A: Given data:- Characteristic strength of cable, fy (cable) = 415 MPa Characteristic strength of…

Q: A cylindrical sample of saturated clay 4 cm in diameter and 8 cm high was tested in an unconfined…

Q: show fbd and complete solution

A: Cable: - It is defined as a flexible structure which is used to support transverse loads that causes…

Q: Solve each problem using the method of consistent deformation. Problem 1 Calculate the reactions on…

Q: A stratum of normally consolidated clay of thickness 10 ft is drained on one side only. It has a…

Q: GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS

A: Disadvantages of using hollow blocks are : High Maintenance cost Load bearing capacity of the wall…

Q: At a given sectiona shaft is subjected to a bending stress of 30 MN/m2 and a shear stress of 60…

Q: moments, draw the shear and moment diagram, and compute for the maximum bending stress if

Q: = 92 mPa and oy = -40 mPa. Determine ox on the plane whose normal are +23° and 23+90°

Q: Solve each problem using the method of least work.

Q: The following data are from a direct shear test on an undisturbed soil sample. Represent the data by…

Q: 2. A load P is supported by two concentric steel springs. The inner spring consists of 30 turns of…

A: Asked: To determine the maximum value of load P carried by two concentric springs. Given: For…

Q: Refer to the soil profile shown in figure below. A laboratory consolidati the results: o'c = 100 kPa…

A: Dry unit weight of sand γdsand=Gγw1+e=2.669.811+0.55=16.835kNm3Sat unit weight of sand…

Q: What is the depth of the flow (m) in a circular channel of diameter 2.0 m for the maximum velocity?

Q: o (ksi) e (in./in.) 33.2 0.0006 45.5 0.0010 49.4 0.0014 51.5 0.0018 53.4 0.0022 Data taken from a…

Q: For a soil with a CBR = 3, a single wheel load = 89 kN 2,000 passes & we can accept 2 to 4 inch…

A: Given Data:CBR=3Wheel load=89kNpasses=2000Ruts=2-4 inchs

Q: Betermine the maximum height of a 3.5' wide by 3.5' long concrete block (y= 150 pcf) with a 2.5' X…

A: Unit weight of concrete = 150 pcf Unit weight of water = 62.43 pcf Let the height of the concrete…

Q: Using method of sections, determine the members BD, CD, and CE. statics of rigid bodies

Q: Situation #1: A reinforced concrete beam has a width of 300 mm and an overall depth of 550 mm. The…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: A supersonic diffuser a fixed geometry 417K 254 and pressure are (K, and KPA), respectively. The…

A: T= 417 K P = 254 kPa A= 0.176 m2 A*=0.149 m2 k= 1.4 (for thermally perfect gas) To find- a) Mach…

Q: How many working hours would it take two (2) steelman to install 3,000kg worth of steel if…

Q: Convert a flowrate of 2029 gal/min to ft /S. Answer to two decimal places.

A: Given data : The value of flow rate=Q Q=2029 gal/min Required : Discharge in ft3/s

Q: 2. For all equations e, if e is quadratic, then e has at most two real solutions. Which of the…

A: Question 2: Given statement: For every equation E: If E is quadratic, then E has at most two real…

Q: How does climate change effect the use of such materials (concrete, steel and timber) in the future…

A: Effect of climate change on concrete:- The endurance of reinforced concrete, which is an important…

Q: 3. Compute the shearing stress if a torque T= 200 N-m is applied to a thin-walled tube having a…

A: In this question or rectangular hexagon is given with thickness of 2 mm the side length of 100 mm…

Q: The 2.4kg particle moves in the horizontal x-y plane and has the velocity shown at time t=0. If the…

A: Given data Mass of particle = 2.4kg Force = Fy = 2 + 3t2/4 Initial velocity = Vi = 5m/s Let the…

Q: rectangular weir is doubly contracted with a width of 1.40m and a flow depth of 0.43m above the…

Q: The coefficient of active earth pressure for a loose sand having an angle of internal friction of…

A: Given data : The value of angle of internal friction=ϕ ϕ=30∘ Required : Coefficient of active…

Q: Drinking water from a dam which undergoes conventional treatment has a computed chlorine demand…

Q: ow does climate change effect the use of such materials (concrete, steel and timber) in the future…

A: Concrete Water in the concrete is evaporated at the high temperature it leads to the formation of…

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

Q: Determine the Maximum Tension in The Cable:

A: Cable: - It is defined as a flexible structure which is used to support transverse loads that causes…

Q: beam has a width of 250 mm and a total depth of 650 mm. it carries a factored moment of 490 kN m.…

Q: 1. A circular sewer pipe 1.6 m in diameter is laid on a slope of 2 m per kilometer. The pipe is made…

A: Given data Shiva Dia is equal to 1.6 Is laid on slope of 2 m per kilometre Mannings constant is…

Q: From the given illustration, give the crystallographic indices and plane. * O [101] and (111) O…

Q: Find the value of coefficient of friction if friction force is 420 N and Normal force is 600 N

Q: consolidation test the following data was obtained: Void ratio of the soil = 0.75; Specific gravity…

Question

A Venturi meter having a throat diameter of 150 mm is installed in a
horizontal 300-mm-diameter water main, as shown. The coefficient of
discharge is 0.982. Determine the difference in level of the mercury columns
of the differential manometer attached to the Venturi meter if the discharge is
142 L/s.
Ans: h= 255 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows through the Venturi meter shown below. The specific gravity of the manometer fluid is 1.52 and water unit weight is 9810 N/m. The discharge coefficient is 0.96. Determine the flowrate, Q.
Installed is a Venturi meter on a pipe 25 cm diameter in which the maximum flow is 150 li/sec and pressure of 6m of water. The throat is 12.5 cm in diameter. Compute the discharge that would be passing through the meter when the differential manometer is as shown:
A 150 mm diameter horizontal Venturi meter is installed in a 450-mm diameter water main. The deflection of mercury in the differential manometer connected from the inlet to the throat is 375 mm. (a) Determine the discharge neglecting head lost. (b) Compute the discharge if the head lost from the inlet to the throat is 300 mm of water, and (c) what is the meter coefficient?
Installed is a venturi meter on a pipe 30 cm diameter in which the maximum flow is 2.7 cum of water in one minute. The throat is 15 cm in diameter. Compute the theoretical discharge that would be passing through the meter when the differetial manometer is as shown. Calculate also the discharge coefficient, C.
Connected to an 18-inch water line is a 6-inch horizontal Venturi meter, with a meter coefficient of 0.94. Theobserved average deflection on the differential manometer from the start of the converging cone to the through is15 inches of a fluid with a specific gravity of 8.0. Compute for the head loss between the inlet and the throat.
a venturi meter having a diameter of 6 in, at the throat is installed in a horizontal 18-in. water main. in a differential gage partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and throat, the mercury column stands 15 in. higher in one leg than the other. what is the discharge through the meter in cubic feet per second: (a.) neglecting friction; (b.) if the loss head between inlet and throat is 1 ft of water? Compute the meter coefficient in (b).
a venturi meter having a diameter of 6 in. at the throat is installed in a horizontal 1-in water main. in a differential gage partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and throat, what would be the difference in level of the mercury columns if the discharge is 5.0 cfs? neglect loss of head.
The throat diameter of a venturimeter is 7.5 cm and the diameter of broader end is 15 cm. A pressure difference of 2.45 m is observed when water is flowing at a rate of 30 lt/sec. COmpute the coefficient of discharge of the venturimeter.
A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming no head loss.
Show all problem solution's steps. Direct formula substitution solutions will have NO CREDIT POINTS. A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The lost head in the nozzle is 25% of the velocity head in the jet. If the pressure at the base of the nozzle is 625 KPa: compute the discharge in m3/min; the maximum horizontal range to which the stream can be thrown; the maximum vertical reach, and the diameter of the jet at a point two-third of the maximum vertical reach from the tip of the nozzle. Neglect air resistance.
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine,(a) Discharge of oil (b) The pressure difference in N/m”2 between entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98*
A Venturi meter 45 cm by 20 cm has its axis inclined upwards 30 degrees from the horizontal. The distance measured along the axis, from the inlet to the throat is 1.20m. The differential manometer connected at the inlet and throat shows a deflection of 25 cm of mercury. If the flow is upward and the flowing fluid has specific gravity of 2.0, find the discharge and the pressure head difference between the inlet and throat if the meter coefficient is 0.96