* A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 65 Btu of heat is transferred to the water, and heat losses from the side walls amount to 8 Btu. The piston rises as a result of evaporation, and 5 Btu of work is done by the vapor. Determine the change in the .energy of the water for this process 61 Btu 52 Btu 60 Btu O 55 Btu O

* A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 65 Btu of heat is transferred to the water, and heat losses from the side walls amount to 8 Btu. The piston rises as a result of evaporation, and 5 Btu of work is done by the vapor. Determine the change in the .energy of the water for this process 61 Btu 52 Btu 60 Btu O 55 Btu O

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

A long roll of 2-m-wide and 0.5-cm-thick 1-Mn manganesesteel plate (ρ = 7854 kg/m3 and cp = 0.434 kJ/kg·°C)coming off a furnace at 820°C is to be quenched in an oil bathat 45°C to a temperature of 51.1°C. If the metal sheet is movingat a steady velocity of 10 m/min, determine the requiredrate of heat removal from the oil to keep its temperature constantat 45°C.
A vertical piston–cylinder device initially contains 0.20 m3 of air at 300 0C by placing 580 kg on the piston (Patm = 97 kPa). The piston has a mass of 5 kg and a diameter of 12 cm. A valve connected to the cylinder is now opened, and air is allowed to escape until three-quarters of the mass leave the cylinder at which point the final temperature in the cylinder is 180 0C. Determine the boundary work during this process. a. 99 kJ b. None of these c. 128 kJ d. 85 kJ e. 115 kJ f. 120 kJ
The work done during the expansion of a gas is 5.31 kJ. The relationship between the pressure and the volumeof the gas is pv2 = c and the initial pressure and the volume are 136 kPa and 0.0425 m3, respectively Determine the final pressure. Ans. 340kPa
A piston-cylinder device initially contains 1.4 kg of refrigerant-134a at 100 kPa and 20oC. Heatis now transferred to the refrigerant from a source at 150oC, and the piston, which is resting on aset of stops, starts moving when the pressure inside reaches 120 kPa. Heat transfer continuesuntil the temperature reaches 80oC. Assuming the surroundings to be at 25oC and 100 kPa,determine the second-law efficiency of this process.
An insulated pipe of inside diameter 50 mm contains steam of specific enthalpy2·794 MJ/kg and specific volume 0·0394 m3 /kg. The pipe then reduces to 25 mmdiameter, and the specific enthalpy is then 2·786 MJ /kg and the specific volume is0·1043 m/kg. Determine the mass flow rate of the steam and its velocity in bothsections of the pipe
An inventor claims to have devised a process using only saturated steam at 100C which by a complicated series of steps, make heat continuously available at T of 177C. He claims further that, for every kilogram of steam taken into the process, 1800 kJ of energy as heat is liberated at this higher T of 177C. Show whether or not such a process is possible. In order to give the inventor the benefit of any doubt, assume cooling water to be available in unlimited quantity at 0C. topic: introduction to chemical engineerint thermodynamics
A 0.75-m3rigid tank initially contains air whose density is 1.18 kg/m3 The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 4.95 kg/m3. Determine the mass of. air that has entered the tank.
A 5 kg/s air enters a device with an initial pressure of 750 kPa, initial velocity of 65 m/s and initial fluid density of 3.2 kg/m3 . The fluid leaves the device at 192 kPa, 155 m/s and 0.87 kg/m3 . The heat loss from the device is 22 kJ/kg and the work done by the fluid is 242kW. Determine the change in internal energy in J/kg.
An air-conditioning system is to befilled from a rigid container that initiallycontains 43 kg of liquid R-134a at 48 °C. Thevalve connecting this container to the airconditioning system is now opened until themass in the container is 2.92 kg, at which timethe valve is closed. During this time, onlyliquid R-134a flows from the container.Presuming that the process is isothermalwhile the valve is open, determine the finalquality of the R-134a in the container and thetotal heat transfer.
A fluid with a pressure of 820 kPa, specific volume of 0.30 m3/kg and a velocity of 150 m/s enters a device. The work done by the fluid is 460 kJ/kg and the heat loss due to radiation is 28 kJ/kg. The exit condition of the fluid are 130 kPa, 0.82 m/kg and 320 m/s. Determine the change in internal energy.
An air-conditioning system is to be filled from a rigid container that initially contains 5 kg of liquid R-134a at 24°C. The valve connecting this container to the air-conditioning system is now opened until the mass in the container is 0.25 kg, at which time the valve is closed. During this time, only liquid R-134a flows from the container. Presuming that the process is isothermal while the valve is open, determine the final quality of the R-134a in the container and the total heat transfer.
A vertical piston–cylinder device initially contains 0.25 m3 of air at 300 0C by placing 600 kg on the piston (Patm = 100 kPa). The piston has a mass of 5 kg and a diameter of 12 cm. A valve connected to the cylinder is now opened, and air is allowed to escape until three-quarters of the mass leave the cylinder at which point the final temperature in the cylinder is 182 0C. Determine the boundary work during this process.