A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of dex) Value of ybar () Location of the Hydro Force measured from the water surface of the gate inclined (yp)l **answer Hydrostatic Force F on the box below: Answer: 1311.03 The correct answer is: 1022.1

A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of dex) Value of ybar () Location of the Hydro Force measured from the water surface of the gate inclined (yp)l **answer Hydrostatic Force F on the box below: Answer: 1311.03 The correct answer is: 1022.1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The air above the liquid is under a pressure of 40 kPa gage, and specificgravity of the liquid in the tank is 0.80. The rectangular gate is 2.0 mwide, y1 = 1.0 m and y2 = 3 m. 1. Determine the hydrostatic force acting on the gate, in kN 2. What is the location of the force, in m, measured from the hinge? 3. Calculate the minimum value of P, in kN, to hold the gate in place
The inclined beam shown is supported by a pin at the left end and a roller at the right end. The rise:run of the beam is h/L=5ft:15ft, what is the actual (sloping) length of the beam? PART A. A vertical point load of P=48 kips is applied at the midspan of the beam. Raplace the point load vector P with its two vector components oriented parallel to the beam (Pa) and paerpendicular to the beam (Pb). State the magnitudes of Pa and Pb. PART B. A vertical distributed load of w=3.2 kip/ft is applied along the length of the beam. Replace the distributed load vector (w) with its two vector components oriented parallel to the beam (wa) and perpendicular to the beam (Wb). What are the magnitudes of Wa and Wb?
The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place.
Obtain the gage pressure at the center A of the pipe shown. Neglect the surface tension effects. Liquid 1, sg=1.5. Liquid 2, sg=3.2, h1=15cm; h2=30 cm; h3=75 cm.
The crankshaft is subjected to a torque of M = 50 N ⋅ m. Determine the horizontal compressive force F applied to the piston for equilibrium when θ = 60°.
A 300-N force is applied to the handle of the winch as shown. The force lies in a plane which is parallel to the y-z plane and is perpendicular to line AB of the handle. Determine the moments of this force about point O.
A cylindrical tank 3m in diameter and 7m high is filled with oil (sg=0.85). The tank is provided by steel hoops. The upper hoop is placed 1m below the top of the tank, while the lower hoop is placed 1m above the bottom of the tank. a.compute the hydrostatic force of oil acting on the wall of the tank, in kN b. determine the tension in the upper hoop in kN. c. Determine the tension in the lower hoop, in kN
GI, GE, and GD of the cage system for the loading condition given in Figure 2 Calculate the rod forces. tensile or tensile rod forces Specify the pressure. P1(kN)=20 P2(kN)=45 L3(m)=7
The 50-lb block and weight (W) is positioned as shown in the figure. The coefficient of static friction between the block and the plane is 0.2 and between the rope and the drum is 0.3. (a) Det. The minimum value of weight (W) which may be applied without causing the 50-lb block to slip.
solve for the total head loss given that the pressure drop between the junction=250kPa. (f=0.02) Use 3 decimal places
Use Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. a=4.5 b=26 c=10 Determine: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.
The uniform slender rod AB shown of weight W is supported by a peg at C and its end A restsagainst a vertical wall. The coefficients of friction at A and Care equal to f. Find the ratio L/a whenmotion is impending. If 0=30" and f=0.3, find the ratio L/a