A W1 L 3 B 13. 3 C mi L 333 W2 D (a) A 12m long beam ABCD is loaded as shown above and rests on foundation (soil) that exerts a linearly varying distributed load on the beam in response t loads. i). Draw the free body diagram for the beam ABCD and determine the magnitude of the load intensities w₁ and w₂ when P = 500 N.

A W1 L 3 B 13. 3 C mi L 333 W2 D (a) A 12m long beam ABCD is loaded as shown above and rests on foundation (soil) that exerts a linearly varying distributed load on the beam in response t loads. i). Draw the free body diagram for the beam ABCD and determine the magnitude of the load intensities w₁ and w₂ when P = 500 N.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fine the residual forces acting in a truce with members AC = 1000N(T), EG = 520N (T), ans FH = 1200N (C) aa indicated below. Determine the loads P1, P2 and P3
A 5.0 simply supported beam is supposed to carry a 2m width concrete slab on its center(unit weight of concreteis 24 kN/m3). The slab thickness is 150mm. On top of slab is a super imposed live load pressure of 14000Pa and supper imposed dead load pressure of 24000Pa. (Use NSCP 2015 Provisions) A.Determine the critical factored moment that the beam will carry. B.If critical factored moment Mu = 380 kN.m, determine the additional unfactored concentrated dead load at midspan of beam. C.If critical factored moment Mu = 400 kN.m, determine the additional service live load pressure on the slab.
A short tied column carries an axial dead load of 1070 kN and live load of 981 kN. If fc' = 27.50 MPa, fy = 413.50 MPa. 1. Which of the following gives the probable size of the tied column. a. 400x400 b. 300x300 c. 500x500 d. 550x550 2. Which of the following gives the number of 28 mm diameter main reinforcing bars. a. 4 bars b. 8 bars c. 6 bars d. 10 bars 3. Which of the following gives the spacing of 10 mm tie wires. a. 300 mm b. 350 mm c. 400 mm d. 500 mm
1. AW610x241 beam 10-meter long is simply supported and is laterally supported throughout its entire span. It is to carry a uniform dead load of 20 kN/m and a uniform live load, both about strong axis. Calculate the maximum uniform live load that the beam can carry. Use Fy = 345 MPa.
A 6-m simply supported reinforced concrete rectangular beam is 250 mm wide. The total depth is 400 mm and its effective depth is 340 mm. It is reinforced for tension only with 4-28mm diameter bars. It carries a total dead load of 21.6 kN/m including its weight. Fy = 350 MPa and f’c = 20.7 MPa. 1. Compute the distance of the neutral axis from the top most fiber. a. 195.98 mm b. 230.56 mm c. 186.01 mm d. 218.84 mm 2. Which of the following gives the ultimate moment capacity of the beam? a. 202.09 kN.m b. 181.88 kN.m c. 171.4 kN.m d. 186.2 kN.m 3. Which of the following most nearly gives the unfactored uniform live load capacity using the load combination 1.2D+1.6L? a. 40.42 kN/m b. 15.38 kN/m c. 9.06 kN/m d. 3.84 kN/m
A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig = 7000x10^6 mm^4, Icr = 3000x10^6 mm^4, uniformly distributed dead load = 5 kN/m, uniformly distributed live load = 7 kN/m, Ec = 21,000 MPa. a) Determine the value of Ma (DL+LL).
A reinforced concrete beam has a width of 425mm and an effectivedepth of 900mm. The longitudinal bars at compression side are 4-25mm dia. and 2layers of 4-32mm dia. at tension side. Concrete strength f’c=27.60 MPa and fy=420.4) Calculate the Transformed moment of Inertia.5) Calculate the moment capacity of the section.6) Calculate for the safest uniform load that can carry by the beam if ihas a lengthof 10m.
Subject: Reinforced concrete Design- Civil Engineering A rectangular beam reinforced for tension has b = 300mm, d = 480mm. The beam is reinforced with 7 of 25mm bars with fc' = 21MPa and fy = 415MPa. If the beam is cantilever, 3m long and supports a uniform dead load of 15kN/m (including its own weight) applied along its entire length, the maximum value of the concentrated live load that can be applied 2m from the free end is kn. Choices: A. 141kN B. 114KN C. 213kN D. 231kN
Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-mcounterclockwise couple (a) Determine the load intensity, w at B and the distance “a” (b) what are thereactions at A and B ?
The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit weight =23.6KN/m^3) resting on the three 8m spanned RC floor beams spaced at 1.6 meters on center. Size of RC beam is 200mm x 450mm. NSCP load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored slab load in KN/m? express your answer in 1 decimal place.
Task 1a. Draw a moment diagram and determine the largest moment at support and field in the below statically indeterminatebeam.b. How much does the largest moment at support and beam change if the length of each bay (L) is increased from 1m to 2m?Assume the load q =10 kN/m . Tip: The task is to make diagrams for the given beam with 2L as total length. What to think about whenusing substitution (L′ = 2L) is to keep track of that variable all the time ultimately the substitutedthe variable is returned for a correct answer. If you make a substitution of the length (L′ = 2L) then it should be returned to the answer. Task 2A cylindrical pin made of carbon steel is loaded with a maximum possible twisting moment Mv. Maximum allowedshear stress is Tmax = 40 MPa. The pin has the diameter measurement d = 50 mm, and the length measurement L = 250 mm.Calculate the free end distortion θ in degrees. G=80 GPa.
Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-mcounterclockwise couple (a) Free Body Diagram (b) Determine the load intensity, w at B and the distance “a” (c) what are thereactions at A and B ?