A W12 x 79 of A572 Grade 60 steel is used as a compression member. It is 28 feet long, pinned at each end, and has additional support in the weak direction at a point 12 feet from the top. Can this member resist a service dead load of 180 kips and a service live load of 320 kips? a. Use LRFD. b. Use ASD.

A W12 x 79 of A572 Grade 60 steel is used as a compression member. It is 28 feet long, pinned at each end, and has additional support in the weak direction at a point 12 feet from the top. Can this member resist a service dead load of 180 kips and a service live load of 320 kips? a. Use LRFD. b. Use ASD.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.3P

See similar textbooks

Similar questions

– A W310 × 97 of A572 Grade 60 steel is used as a compression member. It is 8 meters long, pinned at each end, and has additional support in the weak direction at a point 3.70 meters from the top. Can this member resist a service dead load of 800 kN and a service live load of 1400 kN?a. Use LRFD.b. Use ASD.
Select a rectangular (not square) HSS for use as a 15-foot-long compression member that must resist a service dead load of 35 kips and a service live load of 80 kips. The member will be pinned at each end, with additional support in the weak direction at midheight. Use A500 Grade C steel. a. Use LRFD. b. Use ASD
Design a column base plate for a W10 x 33 column supporting a service dead load of 20 kips and a service live load of 50 kips. The column is supported by a 12-inchx 12-inch concrete pier. Use A36 steel and f ,c= 3 ksi. a. Use LRFD. b. Use ASD
An 80-foot long plate girder (see below) is fabricated from a ½-inch x 78-inch web and two 3inch x 22-inch flanges. Continuous lateral support is provided. The steel is A992. The loading consists of a uniform service dead load of 1.0 kip/ft (including the self-weight), a uniform service live load of 2.0 kips/ft, and a concentrated service live load of 500 kips at midspan. Stiffeners are placed at each end and at 4 feet, 16 feet, and 28 feet from each end. Once stiffener is placed at midspan. Determine whether the flexural strength is adequate using LRFD.
Select the best rectangular (not square) HSS for a column to support a service dead load of 33 kips and a service live load of 82 kips. The member is 27 feet long and is pinned at the ends. It is supported in the weak direction at a point 12 feet from the top. Use Fy 5 46 ksi. a. Use LRFD. b. Use ASD.
A W21 3 68 of A992 steel is used as a simply supported beam with a span length of 50 feet. The only load in addition to the beam weight is a uniform live load. If lateral support is provided at 10-foot intervals, what is the maximum service live load, in kipsyft, that can be supported? a. Use LRFD. b. Use ASD.
Check the shear strength of an interior beam-column joint. The columns have 20 in. square cross-section, and 12ft clear height. The maximum probable moment strength of columns is (Mpr)ed. 520 ft-kips. The framing beams have the following geometry and reinforcement: Mpr = 345 ft-kips and Mpr = 213 ft-Kips; Top Bar = 5- #8 & Bot. Bar = 3 #8 Additional given data: fe= 4,000 psi; fy=60,000 psi
Determine the maximum axial compressive service load that can be supported if the live load is twice as large as the dead load. Use AISC Equation E3-2 or E3-3. a. Use LRFD. b. Use ASD
A 4 × 4 carries an axial compressive force caused by dead, live, and roof live loads. Lumber is No. 1 DF-L. CM = 1.0, Ct = 1.0, and Ci = 1.0. Find: The allowable column load for each load combination if the unbraced length of the member is a. 3 ft b. 6 ft c. 9 ft d. 12 ft
Read the question carefully and give me right solution according to the question. A W12x79 of A573 Grade 60 (Fy=415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at the bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the effective slenderness ratio with respect to strong axis buckling using theoretical value of k.
4.4-2 A W21 × 101 is used as a compression member with one end fixed and the other endfree. The length is 10 feet. What is the nominal compressive strength if Fy = 50 ksi?Note that this is a slender-element compression member, and the equations of AISCSection E7 must be used. 4.6-2 A 15-foot long column is pinned at the bottom and fixed against rotation but free totranslate at the top. It must support a service dead load of 100 kips and a service liveload of 100 kips.a. Select a W12 of A992 steel. Use the column load tables.1. Use LRFD.2. Use ASD.b. Select a W16 of A992 steel. Use the trial-and-error approach covered in Section 4.6.1. Use LRFD.2. Use ASD.
Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method.