A water kettle with a small teapot on top is used to brew tea on top, as shown in the figure. The small teapot may partially block the escape of steam and cause the pressure in the waterpot to rise, and water may spill from the spout of the teapot intended for serving water. Taking into account the thermal expansion of liquid water and the steel pot, the bottom pot is 1 liter and the top pot is 400 ml, the variation of the water in the tube is 3% of the total volume and is not negligible in In relation to the amount of water in the water kettle, determine the maximum height of cold water that would not cause spillage at steam pressures up to 0.32 kPa gauge. Make a matlab program for different volumes of water in the bottom of the kettle from 100ml up to 400ml. P<0.32 kPa (man) Steam 12 cm so ////// heat 40

A water kettle with a small teapot on top is used to brew tea on top, as shown in the figure. The small teapot may partially block the escape of steam and cause the pressure in the waterpot to rise, and water may spill from the spout of the teapot intended for serving water. Taking into account the thermal expansion of liquid water and the steel pot, the bottom pot is 1 liter and the top pot is 400 ml, the variation of the water in the tube is 3% of the total volume and is not negligible in In relation to the amount of water in the water kettle, determine the maximum height of cold water that would not cause spillage at steam pressures up to 0.32 kPa gauge. Make a matlab program for different volumes of water in the bottom of the kettle from 100ml up to 400ml. P<0.32 kPa (man) Steam 12 cm so ////// heat 40

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.4P

See similar textbooks

Similar questions

Warm air is contained in a piston-cylinder assembly oriented horizontally. The aircools slowly from an initial volume of 0.003 m 3 to a final volume of 0.002 m 3 . Duringthe process, the spring exerts a force that varies linearly from an initial value of 900 Nto a final value of zero. The atmospheric pressure is 100 kPa, and the area of thepiston face is 0.018 m 2 .Friction between the pistonand the cylinder wall can beneglected. For the air in thepiston-cylinder assembly,determine the initial and finalpressures, each in kPa andatm.
It is well known that the power consumed by a compressor can be reduced by cooling the gas during compression. Inspired by this, somebody proposes to cool the liquid as it flows through a pump, in order to reduce the power consumption of the pump. Would you support this proposal? Explain.
The chilling room of a meat plant is 15 m × 18 m × 5.5 m in size and has a capacity of 350 beef carcasses. The power consumed by the fans and the lights in the chilling room are 22 and 2 kW, respectively, and the room gains heat through its envelope at a rate of 14 kW. The average mass of beef carcasses is 220 kg. The carcasses enter the chilling room at 35C, after they are washed to facilitate evaporative cooling, and are cooled to 16°C in 12 h. The air enters the chilling room at 2.2°C and leaves at 0.5°C. Determine (a) the refrigeration load of the chilling room and (b) the volume flow rate of air. The average specific heats of beef carcasses and air are 3.14 and 1.0 kJ/kg · °C, respectively, and the density of air can be taken to be 1.28 kg/m3 .
An array of power transistors, dissipating 6 W ofpower each, are to be cooled by mounting them on a 25-cm *25-cm-square aluminum plate and blowing air at 35°C overthe plate with a fan at a velocity of 4 m/s. The average temperatureof the plate is not to exceed 65°C. Assuming theheat transfer from the back side of the plate to be negligibleand disregarding radiation, determine the number of transistorsthat can be placed on this plate.
Consider an air solar collector that is 1 m wide and 5 m longand has a constant spacing of 3 cm between the glass cover andthe collector plate. Air enters the collector at 30°C at a rate of0.15 m3/s through the 1-m-wide edge and flows along the 5-mlong passage way. If the average temperatures of the glasscover and the collector plate are 20°C and 60°C, respectively,determine (a) the net rate of heat transfer to the air in thecollector and (b) the temperature rise of air as it flows throughthe collector.
The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oC
2. A large sheet of glass 2” thick is initially at 300oF throughout. It is plunged into a stream of running water having a temperature of 60oF. How long will it take to cool the glass to an average temperature of 100oF. For glass k = 0.40BTU/ft-hroF, ρ = 155 lb/ft3 and Cp = 0.20 BTU/lboF.
3. Consider a 10-m-long smooth rectangular tube, with a =50 mm and b =25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.
Water is to be heated from 15°C to 65°C as it flows through a 3-cm-internaldiameter 5-m-long tube . The tube is equipped with an electric resistance heater that provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 10 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the tube at the exit.
air at a dry ball temperature of 80 degrees C and 4% RH is passed over the cooling coil so that the temperature of the air dry ball becomes 35 degrees Celsius. how much heat is released from the air in the process? (answer in kj / kg)
An electric water heater has a capacity of 2 liters. In this heater, the water is initially found as a saturated liquid at 150 kPa. When the water is in this state, the heater automatically turns on and heats the water, which expands at a constant pressure through a movable cover mechanism at the top of the heater, which has an associated work done by the system (Ws). Additionally, the electrical resistance supplies 2.2 MJ to the water. These types of heaters have very good thermal insulation and the surroundings are at normal conditions (25°C and 100 kPa). Based on this information: a) Determine the states of the working substance. b) Determine the minimum work (Wmin) with which the process can be carried out. c) Determine the exergy destroyed during this process.
Air with a temperature of 128 °C, a density of 4.89 kg/m3 and a velocity of 121 m/s enters a nozzle with an inlet to outlet area ratio of 2:1 and exits with a density of 2.36 kg/m3. Determine the temperature at the outlet (in K).