A wheel rests at the corner of a block as in the figure. If F is a minimum force required to raise thewheel onto the block, what is the force acting at point A? The block is fixed.F1600mmDIA209BLOCK1000 N250mm 955.7651125.6551260.751O1321.067

Answered: Image /qna-images/answer/5376adf2-3a98-4de4-9289-08e0b3a0343f.jpg

Answered: A wheel rests at the corner of a block…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the moment applied at the end of a flat steel bar 1.2 m long that will produce a midpoint deflection of 40 mm. The flat bar is 75 mm wide and 9 mm thick. Use E = 200000 MPa. a. 404.5 N-mb. 202.5 N-mc. 303.5 N-md. 505.5 N-m
The position of the slider P in the rotating slotted arm OA is controlled by a power screw as shown. At the instant represented, θ˙ = 5.4 rad/s and θ¨ = -35 rad/s2. Also at this same instant, r = 396 mm, r˙ = -251 mm/s, and r¨ = 0. For this instant determine the r- and θ-components of the acceleration of P.
A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Calculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
The 1000N block shown started at rest and moves towards the right. Which if the following gives the distance that 1000N block will travel along the horizontal surface if the coefficient of friction between block and the surface is 0.20. Assume pulley to be frictionless.
Replace the force system acting on the frame by an equivalent resultant force and a couple of moment acting at point A. Suppose that F1 = 300 N and F2 = 100 N Determine the magnitude of the resultant force. Determine the angle between the resultant force and the x axis. Determine the equivalent resultant couple moment about point A.
The belt system is used to transmit power from the motor. If the transmitting power needs to be tripled, and the torque is doubled, what is the correct new operating rotating speed of the shaft in terms of its old speed w(omega)?
A pulley and two loads are connected by inextensible cords as shown. Load A has a constant acceleration of 350 mm/s2 and an initial velocity of 275 mm/s, both directed upward. Determine (a) the number of revolutions executed by the pulley in 5 s,(b) the velocity and position of load B after 5 s, (c) the acceleration of Point D on the rim of the pulley at t = 0. DO NOT ROUND OFF IN THE SOLUTION. ROUND OFF ONLY IN 2 DECIMAL PLACE IN THE FINAL ANSWER
For the built-up shape shown in the figure, determine: a. The location of the plastic neutral axis from the top edge of the flange in mm (ANS 11). b. The plastic section modulus of about the horizontal axis in x106mm3 (ANS 0.214) c. The plastic moment with bending about the vertical axis if Fy = 345 Mpa kN-m. round of to the nearesrt whole number (ANS 43).
The system under the effect of torsion;a- Draw the torsional moment diagram.b- Determine the torsion angle CA (rotation angle) that will occur at point C.c- Determine the load shear stress.(G=80 000 MPa M1=5000Nm M2=4000Nm D1=120mm D2=90 D3=80 D4=60

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A wheel rests at the corner of a block as in the figure. If F is a minimum force required to raise the wheel onto the block, what is the force acting at point A? The block is fixed. F 1600mm DIA 209 BLOCK 1000 N 250mm