A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 11 mm from the top of the beam on a section 3.52 m from A if P = 4626 N, W = 1700 N/m, a = 0.99 m, b = 1.67 m, c = 1.13 m, L = 66 mm and h = 170 mm. Round off the final answer to two decimal places. www P W 커다 A B + b -c→| C h

A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 11 mm from the top of the beam on a section 3.52 m from A if P = 4626 N, W = 1700 N/m, a = 0.99 m, b = 1.67 m, c = 1.13 m, L = 66 mm and h = 170 mm. Round off the final answer to two decimal places. www P W 커다 A B + b -c→| C h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Joists support a floor and transfer their load to beams at each end of each joist. Joists are 2 ft on center and 30 ft long. If w, the load on the floor, is uniformly distributed and is 30 lb/ft2, what is the load on one joist? If the maximum flexural stress S in a joist is given by S = M/Z, where M is the maximum bending moment (pound-foot) and Z is the section modulus (cubic inches), what is the stress in a joist that has a section modulus of 50 in.3 and is 30 ft long? Assume that the maximum bending moment for a simply loaded joist is given by M = wL2/8, If the joists are made of pine, which has an allowable bending stress of 9,300 lb/in.2, will it carry the load?
The reinforced concrete beam has the cross-sectional area shown in the figure with b =12 in., d=16 in., ? steel= 1.571 in.2, determine the largest bending moment that may be applied safely. Takethe elastic moduli ?steel=29(10^3) ksi and ?concrete= 3.6(10^3) ksi. The working stresses are2.39ksi for concrete and 22.145ksi for steel.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.7 in from the top of the beam on section 2.05 feet to the right of B if P = 1080 lb, Q = 4215 lb, w = 1.08 in, L = 8.26 in, b = 3.97 in, and h = 1.25 in. Round off the final answer to two decimal places
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
Refer to the figure: What is the flexural stress in psi, 3 inches from the top of the beam and 2 feet from the left end of the beam? What is the maximum bending moment?
A beam has a cross section show below. If the stress at point P is 30Kpa , calculate the value for the shear force V. can you please show details? especially how to calculate the moment of inertia. I got a first response but I got confuse how the person use the parameters to calculate INERTIA
A steel rod with a diameter of 12 mm, on which two points were fixed, with a distance of 75 mm between them, and then a pulling force of 10.5 kilonewtons was applied to it, so the distance between the two points increased by 0.035 mm and the diameter decreased by 0.0015 mm. What is the stress generated in the steel bar in megapascals? What is the type of stress generated? What is the amount of longitudinal strain? What is the amount of transverse strain? What is the modulus of elasticity for the steel rod?
A beam constructed from 2-in. by 8-in. boards has the cross section shown in the figure. If the maximum bending moment acting in the beam is M= 16 000 lb ft, determine the maximum bending stress in (a) board A; and (b) board B.
For the beam shown, calculate the bending stress at a point 70 mm. from the top of the beam. P = 59, a = 233, b = 296 Round your answers to 2 decimal places.
A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4141 N, W = 1010 N/m, a = 1.15 m, b = 2.25 m, c = 1.2 m, L = 81 mm and h = 297 mm.
strength of materials... answer only A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 34 mm from the top of the of the beam on a section 1.66 m from A if P = 5381 N, W = 2349 N/m, a = 1.31 m, b = 2.12 m, c = 1.27 m, L = 72 mm and h = 239 mm. Round off the final answer to two decimal places.