A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4564 N, W = 1694 N/m, a = 1.08 m, b = 2.13 m, c = 1.04 m, L = 86 mm and h = 266 mm. Round off the final answer to two decimal places. W P 커다 A de b .c→ C h

A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4564 N, W = 1694 N/m, a = 1.08 m, b = 2.13 m, c = 1.04 m, L = 86 mm and h = 266 mm. Round off the final answer to two decimal places. W P 커다 A de b .c→ C h

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.13.3P: A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h =...

See similar textbooks

Related questions

Q: If Reynolds number relate the inertial and viscous forces, which of the following relates the…

A: The correct option is (A) I.e., FROUDE NUMBER (Fr) In the dimensional and modal analysis, we have…

Q: (14) Which of the following is not an exact differential? O du Ods dw dH 15) Enthalpy is defined as…

A: 1.i) dU 2.iii) H= U+pv 3.iii) thermodynamics

Q: What kind of circuit balancing valve is used in the hot and chilled water piping? a. balancing…

A: Concept: 1.In chiller, after condenser the refrigerant fluid is passed through capillary valve…

Q: 4. Steam at 18 Mpa, T = 357.06 C 5. Steam at P = 19 Mpa, T = 100 degC SH 6. Saturated vapor at 5.4…

Q: he power requirement of a 3-stage compressor (in kW, two decimal places) in order to supply air at…

A: Given:T=20° CQ=250 m3/hrP=100 psig =689.47 KPaη=60%

Q: A set of spur gear transmits 30 kW when the pinion rotates at 400 rpm the gear ratio is 1:4. The…

Q: MomentB. A 1.0 [kg] ball moving east collides head-on with a 2.0 [kg] ball that is also moving east…

Q: The flow pattern can be controlled by which equipment or part of the vessel? A. Baffles B. Impellers…

A: To find : The flow pattern can be controlled by which equipment or part of the vessel

Q: A ball is shot vertically into the air at a velocity of 60 m/s. After 5 seconds, another ball is…

Q: the mercury 2. Mercury is poured into the tube in the figure until occupies 375 mm of the tube's…

A: Consider the length of the mercury above the horizontal surface.x1 + x2 =375 mm - 160 mm x1 = 215…

Q: Find the moment of inertia about centroidal axis of I section.

Q: A 2494 lb car is moving up a 13 degree incline as shown. If it took 7 s for the car to decelerate…

Q: Toluene at 35 degrees Celsius is pumped from an open reservoir to a tank kept at a gauge pressure of…

A: Temperature of Toluene, T=35oCDischarge tank pressure, P1=150 kPa=150*103 PaPosition of pump below…

Q: A weir is used to: * O measure the flow rate of open-flowing liquids control the flow rate of an…

A: A weir is used to measure flow rate of open flow liquid Option a is correct

Q: The box of negligible size is sliding down along a curved path defined by the parabola y = 0.4x².…

Q: M Calculate the ratio of bi to b₂ he allowable stresses in tension

Q: 3. Assume there is friction head loss in the siphon as shown in the Fig. 2.1, where a = 1 m, b = 4…

A: Introduction: When fluid flow through the pipe there are two losses that come into the picture one…

Q: Locate the centroid

Q: UN TA Istap. A constant "force" F = 5.0 [N] is applied at a certain angle from the horizontal on a…

Q: Consider a modification of the cold air-standard Otto cycle in which the isentropic compression and…

Q: Find the total change in entropy if 2kg2kg of ice at 0.0∘C0.0∘C is mixed with 25kg25kg of water at…

Q: At time t = 0, a particle is at rest in the x-y plane at the coordinates (xo, yo) = (8,0) in. If the…

A: Given data: At t=0 sec,x0,y0=8,0 inax=0.53-0.27t in/s2ay=0.13t-0.04t2 in/s2 Need to determine the…

Q: Two flat bars loaded in tension by forces P are spliced using two rectangular splice plates and two…

A: The allowable value of load P is 6.14 kips.

Q: A spring of force constant 800Nm¹ is stretched initially by 5 cm. The work done stretching form 5 cm…

A: From the data given in question, Spring constant = k = 800 N/m Initial stretch of spring = x1 = 5 cm…

Q: A horizontal venturi meter having a throat diameter of 25 mm is set in a 60-mm-ID pipeline. Water at…

Q: A piece of lead (sp. Gr. 11.3) is tied to a 130 cc of cork whose specific gravity is 0.25. they…

Q: Calculate the difference between the free surface SG=0.90 1 m Water I 0.4 m Ilk JI*** Ah

Q: From the given beam shown below, find the shear value on segment BC (VBC). 40kr/m 75kum Тв ↓ Im +

A: Given data: w=40 kN/mM=75 kN.m Need to determine the shear force value in segment BC.

Q: Large cut. From a circular disk with uniformly distributed mass M and radius R, a smaller circle of…

Q: s, please help

A: R-134aP1=4 barP2=10 barT2=90°Cm˙=7kg/minPin=10.85kW˙ To-Find:- Qcv˙=?

Q: A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m…

A: Dear student, According to guidelines, I am allowed to answer only one problem…

Q: TRUE or FALSE Pitot tube is an insertion meter. When this is located at the center, the flow that…

A: Solution is attached below:

Q: 1. Using the conjugate beam method, determine the slope and deflection at point B of the beam ABC…

Q: Consider the structure below, the components of the reaction force at C are Cx = -N. 500x _N and Cy=

Q: Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN…

Q: 3. Assume there is friction head loss in the siphon as shown in the Fig. 2.1, where a = 1 m, b = 4…

Q: A vertical force of 10 kN is applied to point C in the plane truss system shown in the figure.…

Q: QUESTION 2 A 1.5 m diameter cylinder of 1.5 m length is immersed in water as shown in figure 1.…

Q: Solve for the Following Shear force equation for segment AB. a.-16.65 psf X squared b. 16.65…

Q: I put Php10,000 into a fund today which earns 8% compounded annually. One year from now, I put in…

A: Please find the solution below

Q: Determine the pressure of nitrogen at 160K,v=0.00291m3/kg der Waals EOS, and the nitrogen table.…

Q: 4. If 6.5 m³ of oil weighs 46,800 N, calculate its density in kg/m³. (a) 285 (b) 258 (c) 82 (d) 734

A: Given : volume of oil , V = 6.5 m3 weight of oil , W = 46800 N To find : density

Q: Tem 9.8 A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal…

Q: The constant angular acceleration of the rotating disk is 12 rad/s2 . The angular velocity of the…

A: The total angle turned by the disk is 192 radians.

Q: A pitot tube is used to measure the flow rate of water at 30C. The pitot tube is positioned at the…

Q: The power winches on the industrial scaffold enable it to be raised or lowered. For rotation in the…

Q: Instructions: Draw the shear and bending moment diagram of each beam loaded as shown. Show your…

Q: • A prismatic beam of trapezoidal section shown in figure is subjected to sagging B.M Calculate the…

A: When a beam having Young's Modulus of Elasticity E is subjected to Bending Moment M then, bending…

Q: A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5;…

Q: A piston-cylinder device initially contains 1.5 kg saturated vapour of an unknown refrigerant at 200…

A: At 200 kPa and -10oC, a piston cylinder device holds 1.5 kg saturated vapour of an unknown…

Question

A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4564 N, W = 1694 N/m, a
= 1.08 m, b = 2.13 m, c = 1.04 m, L = 86 mm and h = 266 mm. Round off the final answer to two decimal places.
...
W
P
+²+
A
B
+
b
C
I

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:

VIEW

Step 2:

VIEW

Step 3:

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross section of a rectangular beam having a width b and height h is shown in part a of the figure. For reasons unknown to the beam designer, it is planned to add structural projections of width b/9 and height d/9 the top and bottom of the beam (see part b of the figure). For what values of d is the bending-moment capacity of the beam increased? For what values is it decreased?
The cross section of a sand wie h beam consisting of aluminum alloy faces and a foam core is shown in the figure. The width b of the beam is 8.0 in, the thickness I of the faces is 0.25 in., and the height hcof the core is 5.5 in. (total height h = 6.0 in). The moduli of elasticity are 10.5 × 106 psi for the aluminum faces and 12.000 psi for the foam core. A bending moment M = 40 kip-in. acts about the z axis. Determine the maximum stresses in the faces and the core using (a) the general theory for composite beams and (b) the approximate theory for sandwich beams.
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q = 3.0 kips/ft on a span of length L = 12 ft (sec figure). The dimensions of the cross section are q = 10.5 in., b = 5.81 in., t1= 0.510 in., and fw = 0.300 in. Calculate the maximum shear stress tjuly on cross section A—A located at distance d = 2.5 ft from the end of the beam. Calculate the shear stress rat point Bon the cross section. Point B is located at a distance a = 1.5 in. from the edge of the lower flange.
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 0,88 in. and h1 = 0.80 in. The maximum allowable bending stress in the metal beam is emax = 60 ksi, and the bending moment is M = 600 lb-in. Determine the minimum permissible width bminof the beam.
A wood beam reinforced by an aluminum channel section is shown in the figure. The beam has a cross section of dimensions 150 mm x 250 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 M Pa and 38 M Pa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam?
A W 12 x 50 steel wide-flange beam and a segment of a 4-inch thick concrete slab (see figure) jointly resist a positive bending moment of 95 kip-ft. The beam and slab are joined by shear connectors that are welded to the steel beam. (These connectors resist the horizontal shear at the contact surface.) The moduli of elasticity of the steel and the concrete are in the ratio 12 to 1. Determine the maximum stresses r1 and xtin the steel and concrete, respectively. Note: See Table F-l(a) of Appendix F for the dimensions and properties of the steel beam.
The hollow box beam shown in the figure is subjected to a bending moment M of such magnitude that the flanges yield but the webs remain linearly elastic. (a) Calculate the magnitude of the moment M if the dimensions of the cross section are A = 15 in., A] = 12.75 in., h = 9 in., and ey =7.5 in. Also, the yield stress is eY = 33 ksi. (b) What percent of the moment M is produced by the elastic core?
A weight W = 20 kN falls through a height h = 1,0 mm onto the midpoint or a simple beam of length L = 3 m (see figure). The beam is made of wood with square cross section (dimension don each side) and E = 12 GPa. If the allowable bending stress in the wood is °aLLow =10MPa, what is the minimum required dimension
Two identical, simply supported beams AB and CD are placed so that they cross each other at their midpoints (sec figure). Before the uniform load is applied, the beams just touch each other at the crossing point. Determine the maximum bending moments (mab)max* and (MCD)max beams AB and CD, respectively, due to the uniform load if the intensity of the load is q = 6.4 kN/m and the length of each beam is L = 4 m.
A hollow box beam with height h = 9.5 in., inside height/i, = 8.0 in., width? = 5,25 in., and inside width =4.5 in. is shown in the figure. Assuming that the beam is constructed of steel with yield stress ty= 42 ksi calculate the yield moment My, plastic moment MPand shape factor f.
A composite beam consisting of fiberglass faces and a core of particle board has the cross section shown in the figure. The width of the beam is 2,0 in., the thickness of the faces is 0,10 in., and the thickness of the core is 0.50 in. The beam is subjected to a bending moment of 250 lb-in, acting about the - axis. Find the maximum bending stresses tr(and ctc in the faces and the core, respectively, if their respective moduli of elasticity are 4 x 106 psi and 1.5 x 106 psi.