A wooden beam and a steel plate will be attached with three steel bolts. If the plate will be loaded with 120 kN, determine the necessary diameter for the bolts. Assume an ultimate shear stress corresponding to half the ultimate normal stress, for a tool steel, and a factor of safety of 3.25. Sound good material?

A wooden beam and a steel plate will be attached with three steel bolts. If the plate will be loaded with 120 kN, determine the necessary diameter for the bolts. Assume an ultimate shear stress corresponding to half the ultimate normal stress, for a tool steel, and a factor of safety of 3.25. Sound good material?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.32P

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
A drill rod with a diameter of 12 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90⁰ with respect to the other end without exceeding an allowable shear stress of 300 MPa?
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
An AISI 1035 CD steel tube has an OD = 45 mm and a wall thickness of 5 mm. What maximum external pressure can this tube withstand if the largest principal normal stress is not to exceed 80 % of the minimum yield strength of the material? Assume ?? = 0.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
A circular dise of 150 min diameter and 10 mm thickness is compressed between two flat dies, and μ = 0.1 determine sticking radius and load on dies if avg. yield stress is 200 N/mm².
A 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force tangent to pulley rim in kN will crush the key if bearing stress is 50 ksi? Assume key and shaft are of the same material.
A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum ten sile stress allowed in the material is 30MPa. Calculate the safe load the stud can carry.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Hexagonal nuts for 6.25mm diameter bolts have a height of 5.5mm. If the ultimate strength of the nut material in shear is 103MPa, what is the most nearly the maximum allowable shear force on the nut thread using a safety factor of 5?