A wooden beam is fabricated by bolting together three members. The cross-sectional dimensions are shown. The 7-mm-diameter bolts are spaced at intervals of s- 100 mm along the x axis of the beam. If the internal shear force in the beam is V-11 kN, determine the shear stress r in each bolt. Assume by - 46 mm, b₂-39 mm, dy-62 mm, d₂-290 mm.

A wooden beam is fabricated by bolting together three members. The cross-sectional dimensions are shown. The 7-mm-diameter bolts are spaced at intervals of s- 100 mm along the x axis of the beam. If the internal shear force in the beam is V-11 kN, determine the shear stress r in each bolt. Assume by - 46 mm, b₂-39 mm, dy-62 mm, d₂-290 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel plate 2.5 m x 1.6 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the shear stress (MPa) in the 16 mm diameter pins through the clevis The correct answer is 45.33. Show solution.
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
The timber member BC, inclined at angle 0 = 60° to the vertical, is supported by a pin at B and the 0.75-in.-diameter steel bar AC. (a) Determine the cross-sectional area of BC for which the displacement of C will be vertical when the 5000-1b force is applied. (b) Compute the corresponding displacement of C. The moduli of elasticity are 1.8 x 106 psi for timber and 29 x 106 psi for steel. Neglect the weight of BC.
For the triangular beam with base b= 400mm and d=540mm determine the area of the compression stress block (shaded in green) if a=210mm. Assume d'=60mm. Ans in mm2. Do not write the units in your answer.
Determine the normal stress (in psi) at point C for the b=2.4-in. by h= 6.1-in. wooden beam shown below if X = 2.9 ft, P = 1201 lb, and θ = 34° . Round off final answer to four decimal places.
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k
(a) Determine the deflection of the beam at point D by both Virtual Work Method and Castigliano’s Theorem. Compare and comment on the differences in these approaches. (b) Calculate the bending and shear stresses at point F on the Section B-B (c) Develop and sketch the Mohr’s circle of stresses corresponding to point F. Show all necessary details, including principal stresses and maximum shear stress.
Determine the normal stress (in psi) at point D for the b=2.1-in. by h= 6-in. beam shown below if X = 6.97 in, P = 9468 lb, and F = 2714 lb. Round off final answer to four decimal places.
The 1.25-in diameter steel shaft BC is built into the rigid wall at C and supported by a smooth bearing at B. The lever AB is welded to the end of the shaft. Determine the force P that will produce a 2-in. vertical displacement of end A of the lever. What is the corresponding maximum shear stress in the shaft? Use G = 12 x 106 psi for steel, and neglect deformation of the lever. Please write legibly, thank you
The cantilever beam AB, with the rectangular cross section shown, is supported by a 1/8-in.-diameter steel wire at B. The force in the wire was stress-free before the uniformly distributed load was applied. The beam and the wire are both made of steel with E = 29 x 10^6 psi. Determine the force in the steel wire and the elongation of the steel wire. What is the moment at A?