a. A stainless-steel ring is 50 mm diameter and 2 mm thickness must be fitted into a steel shaft with 50.04 mm diameter. If the initial temperature is 20° C and the coefficient of linear expansion is 15x106 per degree C (17.3 x 10-6 per Kelvin). Work out the temperature, which is required to fit the ring on the shaft. Also calculate the stress and force induced to the ring if the young's modulus of steel is 205 GPa.

a. A stainless-steel ring is 50 mm diameter and 2 mm thickness must be fitted into a steel shaft with 50.04 mm diameter. If the initial temperature is 20° C and the coefficient of linear expansion is 15x106 per degree C (17.3 x 10-6 per Kelvin). Work out the temperature, which is required to fit the ring on the shaft. Also calculate the stress and force induced to the ring if the young's modulus of steel is 205 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the clearance between 10 m steel railroad rails. The lowest temperature considered is 16 C and a maximum temperature of 36 C. Assume coefficient of thermal expansion of steel to be 11.5 x 10-61/°C. A)3.22mm B)4.16mm C)3.42mm D)2.32mm
f’c = 28 fy = 415 Mpa ex= 320mm a. Calculate depth of neutral axis b. Calculate the stress in extreme compression reinforcement in Mpa
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
A fluid having a specific gravity of 0.869 and dynamic viscosity of 0.0814 Pa-s flows through a cast iron pipe at a velocity of 1m/s. The pipe is 50 m long and has a radius of 75mm. Solve for the shearing stress at the walls of the pipe in Pa. Round your answer to 2 decimal places.
solve for the total head loss given that the pressure drop between the junction=250kPa. (f=0.02) Use 3 decimal places
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center O, the spool has a larger radius R=0,17 and an inner radius r=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel (Please make the diagram well drawn). b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N , and its center of gravity is located at its geometric center O, the spool has a larger radius R=0,17 and an inner radius r=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
A 150mm x 150mm square metal plate, 10mm thick, is hinged about a horizontal edge. If a 10mm diameter horizontal jet of water impinging 50mm below the hinge keeps the plate inclined at 30 degrees to the vertical, find the velocity of the jet. Take the specific weight of the metal as 75kN/m^3.
Determine wether the block shown is in equilibrium and find the magnitude and direction of the friction force. The co efficient of static friction us, for all surfaces is 0.25 and uk= 0.15
A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. What normal tension ( N ) is required in order that the effect of sag will be eliminated when the tape is supported at end points only? The standard pull is 10kg. Tape area is 8 mm2. E = 200 GPa. need answers and solutions asap, thank you!